background image

Sony EMCS Co.

2005L1600-1

  ©2005.12

Published by DI Technical Support Department

9-876-862-11

MPK-DVF7

MPK-DVF7

MARINE PACK

MPK-DVF7

US Model

Canadian Model

AEP Model

SERVICE MANUAL

Ver 1.1  2005. 12

SPECIFICATIONS

• INSTRUCTION MANUAL is shown at the end of this document.

Features and Precautions

• This marine pack can be used with the following Sony Handycam camcorders:

NTSC system-based: DCR-HC90/HC43/HC42/HC40/HC33/HC32/HC30/HC21/HC20/
DVD803/DVD703/DVD653/DVD602/DVD403/DVD203/DVD103/DVD92/PC109/PC108/
PC107

PAL system-based: DCR-HC90E/HC43E/HC42E/HC40E/HC39E/HC33E/HC32E/HC30E/
HC22E/HC21E/HC20E/HC19E/HC18E/HC17E/DVD803E/DVD703E/DVD653E/
DVD602E/DVD403E/DVD203E/DVD202E/DVD103E/PC109E/PC108E/PC107E/PC106E

• Recording at depths of up to 75 meters (246 feet) is possible.

• The following operations can be performed underwater.

Power on/off

Recording start/stop

Auto focusing on/off

Tape photo recording

Electric zoom function

• LCD screen monitor.

O-ring maintenance is very important. If O-ring maintenance is not
followed according to instructions, a water leak may occur and
cause the marine pack to sink. Waterproofing is achieved by
perfect sealing of the O-ring to the entire contact surface.

About the LCD monitor

• Install the camcorder in the marine pack and set the POWER switch to ON to make images

appear on the LCD monitor.

• The remaining battery time indicator displayed on the LCD monitor refers to remaining time of

the camcorder battery time, not the remaining time of the LCD monitor battery.

• You can use the monitor for approximately 6 hours with four new AA alkaline dry batteries.

Содержание MPK-DVF7 O-ring





































Отзывы: