27
General
Outputs:
Audio outputs terminal (front, sub/rear switchable)
Subwoofer output terminal (mono)
Power antenna (aerial) relay control terminal
Power amplifier control terminal
Inputs:
Remote controller input terminal
Antenna (aerial) input terminal
Telephone ATT control terminal
BUS control input terminal
BUS audio input terminal
AUX input jack (stereo mini jack)
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements:
12 V DC car battery
(negative ground (earth))
Dimensions:
Approx. 178
×
50
×
179 mm
(7
1
/
8
×
2
×
7
1
/
8
in) (w/h/d)
Mounting dimensions:
Approx. 182
×
53
×
162 mm
(7
1
/
4
×
2
1
/
8
×
6
1
/
2
in) (w/h/d)
Mass:
Approx. 1.2 kg (2 lb 11 oz)
Supplied accessory:
Card remote commander: RM-X304
Parts for installation and connections (1 set)
Optional accessories/equipment:
Rotary commander: RM-X4S
BUS cable (supplied with an RCA pin cord):
RC-61 (1 m), RC-62 (2 m)
CD changer (6 discs): CDX-T69
Source selector: XA-C40
Interface adaptor for iPod: XA-120IP
Your dealer may not handle some of the above listed
accessories. Please ask the dealer for detailed
information.
Design and specifications are subject to change
without notice.
Troubleshooting
The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check the
connection and operating procedures.
If the problem is not solved, visit the following
support site.
• Halogenated flame retardants are not used in the
certain printed wiring boards.
• Halogenated flame retardants are not used in
cabinets.
• Packaging cushions are made from paper.
General
No power is being supplied to the unit.
• Check the connection or fuse.
• If the unit is turned off and the display disappears, it
cannot be operated with the remote commander.
t
Turn on the unit.
The power antenna (aerial) does not extend.
The power antenna (aerial) does not have a relay box.
No sound.
• The ATT function is activated, or the Telephone ATT
function (when the interface cable of a car telephone
is connected to the ATT lead) is activated.
• The position of the fader control “FAD” is not set for
a 2-speaker system.
• The Bluetooth audio device is in pause.
t
Cancel pause.
No beep sound.
• The beep sound is canceled (page 20).
• An optional power amplifier is connected and you are
not using the built-in amplifier.
The contents of the memory have been erased.
• The RESET button has been pressed.
t
Store again into the memory.
• The power supply lead or battery has been
disconnected or it is not connected properly.
Stored stations and correct time are erased.
The fuse has blown.
Makes noise when the position of the ignition
is switched.
The leads are not matched correctly with the car’s
accessory power connector.
During playback or reception, demonstration
mode starts.
If no operation is performed for 5 minutes with
“DEMO-ON” set, demonstration mode starts.
t
Set “DEMO-OFF” (page 20).
The display disappears from/does not appear
in the display window.
• The dimmer is set “DIM-ON” (page 20).
• The display disappears if you press and hold
(OFF)
.
t
Press and hold
(OFF)
on the unit until the
display appears.
• The connectors are dirty (page 25).
continue to next page
t
Support site
http://support.sony-europe.com/
