Sony MEX-BT3800U - Bluetooth Audio System Скачать руководство пользователя | Manualshive

Страница: 4 / 50

background image

MEX-BT38UW/BT3800U/BT3807U/BT3850U

4

SECTION 1

SERVICING NOTES

NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The

fl

exible board is easily damaged and should be handled with

care.

NOTES ON LASER DIODE EMISSION CHECK

Never look into the laser diode emission from right above when
checking it for adjustment. It is feared that you will lose your sight.

If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-

fi

xed resistor located at the side of optical

pick-up block.

optical pick-up

semi-fixed resistor

EXTENSION CABLE AND SERVICE POSITION

When repairing or servicing this set, connect the jig (extension
cable) as shown below.

• Connect the MAIN board (CN350) and the SERVO board

(CN401) with the extension cable (Part No. J-2502-076-1).

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(

Caution:

Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to
about 350 °C.

Caution:

The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong

viscosity

Unleaded solder is more viscous (sticky, less prone to

fl

ow)

than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

TEST DISCS

Use following TEST DISC when this set con

fi

rms the operation

and checks it.

3-702-101-01

YEDS-18 (for CD)

4-225-203-01

PATD-012 (for CD)

NOTE FOR THE 20-PIN CONNECTOR (CN901)

Do not use alcohol to clean the 20-pin connector (CN901) connect-
ing the front panel with the main body.
Do not touch the connector directly with your bare hand. Poor con-
tact may be caused.

SERVO board
(CN401)

MAIN board
(CN350)

extension cable
(Part No. J-2502-076-1)

Part No.

Description

«
...
2
3
4
5
6
...
»

Содержание MEX-BT3800U - Bluetooth Audio System



















































Отзывы:

Нет отзывов

Похожие инструкции для MEX-BT3800U - Bluetooth Audio System

Бренд: R&S Страницы: 183

Бренд: AccessPRO Страницы: 8

Бренд: Gallagher Страницы: 13

Бренд: Quark-Elec Страницы: 2

Бренд: Teac Страницы: 36

Бренд: X10 Страницы: 1

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 67

Бренд: Yamaha Страницы: 54

Бренд: Yamaha Страницы: 70

V665 - RX AV Receiver

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 478

Бренд: Yamaha Страницы: 18

Бренд: Yamaha Страницы: 68

Бренд: Yamaha Страницы: 143

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды