Sony LT39h Скачать руководство пользователя страница 58

Страница: 58 / 63

Troubleshooting Guide (mech)

1277-9814 Rev



Sony Ericsson Mobile Communications AB – Company Internal

58(63)

Problem Areas

1.34 Charging

1.34.1 Battery will not charge by USB
connector

Check:

Inspect the USB connector.

Action:

1. If dirty or oxidized – clean the connector.
2. Replace Main PBA.

Check:

Inspect the BtB Connector of the Battery to Main PBA.

Action:

1. If not properly connected – disconnect and reconnect it.
2. If dirty or oxidized – clean the both sides of the BtB

connector.

3. If the BtB connector, the Battery FPC or Battery is
damaged – replace the Battery.
4. Replace Main PBA.

1.34.2 Battery will not charge by
charge pad

Check:

Inspect the external port of the Magnetic Charger
Connector.

Action:

If dirty or oxidized – clean it.

Содержание LT39h
































































Результаты поиска

Содержание LT39h

Отзывы:

Похожие инструкции для LT39h

Бренды по названию

Популярные бренды

Sony LT39h, Руководство по устранению неисправностей

Результаты поиска

Содержание LT39h

Отзывы:

Похожие инструкции для LT39h

Бренды по названию

Популярные бренды