Sony LT39h Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 63

background image

Troubleshooting Guide (mech)

1277-9814 Rev

2



Sony Ericsson Mobile Communications AB – Company Internal

14(63)

Problem Areas

1.4 Display

1.4.1 Graphics & Illumination

Check:

Check whether the phone vibrates after the on/off key has
been pressed.

Action:

If the activation described above is not detected, refer to
section 1.1 ‘Power’.

Check:

Inspect the BtB connector of FPC Assembly Relay to Main
PBA.

Action:

1. If not properly connected – disconnect and reconnect it.
2. If dirty or oxidized – clean it.

3. If the BtB connector of FPC Assembly Relay or FPC is
damaged – replace the FPC Assembly Relay.

Check:

Inspect the BtB connector of FPC Assembly Relay to Front
Cover and the BtB and ZIF connector of Front Cover.

Action:

1. If not properly connected – disconnect and reconnect it.
2. If dirty or oxidized – clean it.

«
...
12
13
14
15
16
...
»

Содержание LT39h
































































Отзывы:

Нет отзывов

Похожие инструкции для LT39h

Univerge SV 9500

Бренд: NEC Страницы: 2

Yealink SIP-T46G

Бренд: Yealink Страницы: 8

Бренд: Samsung Страницы: 265

Бренд: Samsung Страницы: 108

Бренд: Yealink Страницы: 8

Бренд: Ericsson Страницы: 76

Бренд: Verykool Страницы: 30

INNOVAPHONE 200

Бренд: TIPTEL Страницы: 32

Бренд: Sony Ericsson Страницы: 54

Бренд: ATCOM Страницы: 60

HANDLEPLUS 326I GSM

Бренд: Doro Страницы: 280

Бренд: HTC Страницы: 16

Бренд: jablotron Страницы: 11

Бренд: ALIGATOR Страницы: 30

Бренд: Archos Страницы: 180

Бренд: NEO Страницы: 61

Бренд: Inter-Tel Страницы: 86

Бренд: Samsung Страницы: 184

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды