Sony KDL-22EX355 Скачать руководство пользователя страница 18

Страница: 18 / 46

KDL-22EX355/32EX355/40EX455 9

SECTION 2 - TROUBLESHOOTING

6X Blink - Backlight Inverter System Failure

If the inverter circuits fails to generate high voltage or one or more of

the backlight fails to light, the television will shut down and display this

diagnostics error.

7X Blink - Temperature Failure

A digital thermometer IC located on the Main Board provides a temperature

reading of the chassis and LCD panel. If the temperature exceeds a pre-

determined point the TV will shut down. If this problem occurs immediately

at turn-on, the temperature sensing IC has failed and replacing the main

board is required. If this occurs after the TV has been running for a while,

check for ventilation issues that could cause the TV to run hotter than

normal.

TRIAGE CHART

Use this general Triage Chart to determine what may possibly be causing the error before going out to the customers location.

1. Confirm the symptom from the customer.

RED DOT: (Primary) Most likely defective part

2. Select that symptom from the chart.

BLUE Triangle: (Secondary) Possible defective part

3. Bring the primary component listed for that symptom.

5. Chart Color Code

Power

Audio

2X 3X 5X 6X 7X

Dead set

Video

Whole

Screen

Distortion

Isolated

Area

Distortion

No Audio

Main Board



▲



Power Supply



***



H Board

LCD Panel



TCON



▲

4. Follow the associated flowcharts in the Training Manual to isolate the board.

Board



* TV Immediate Shuts Off After Power ON & 7X



***Backlight Does NOT Turn ON before TV Shuts

*NOTE:

REFER TO LCD PANEL SERVICE

MANUAL IN REFERENCE LIBRARY DATABASE

FOR CORRECT REPLACEMENT PARTS BASED



**Backlight Turns ON before TV Shuts Off

Video

Protection Modes

Содержание KDL-22EX355















































Результаты поиска

Содержание KDL-22EX355

Отзывы:

Бренды по названию

Популярные бренды

Sony KDL-22EX355, Руководство по обучению обслуживанию

Результаты поиска

Содержание KDL-22EX355

Отзывы:

Бренды по названию

Популярные бренды