Sony IT-M804 Скачать руководство пользователя | Manualshive

Страница: 71 / 80

background image

Additional Information

Additional Information

71

US

Using the phone during a power failure

During a power failure, you cannot make or receive calls. When power
returns, reset the date and time. Other settings and memory will return as
they were before the power failure.

We recommend that you install the 6F22/6LR61 9V battery (not supplied)
into the phone.

When you install the

6F22/6LR61 9V battery (not supplied) into

the phone

During a power failure, you can make or receive calls. However, the
speakerphone does not function. To make a call, you must press the line
button after picking up the handset, and to receive a call, press the line
button which is flashing after picking up the handset.

The phone can be used for about 30 minutes continuously.

When making a call, you can only use the dialing keys.

During a power failure, “POWER FAILURE” appears on the display.

In the following cases, the battery has been exhausted so it needs to be
replaced.

• When calls cut out during a conversation.
• When the line button does not light up or goes off quickly even if the line

button is pressed after picking up the handset.

• When the display of “POWER FAILURE” becomes weak.
• A clicking noise may be heard from the phone.

Notes

• You cannot operate the phone other than for making or receiving calls.
• If the AC adaptor is pulled out from the AC outlet when the battery is still inside

the phone, the battery will discharge even if the phone is not being used. Remove
the battery when unplugging the phone for a long time in order to avoid battery
discharge and damage to the phone from battery leakage.

• If there is a power failure during a call with intercom, page, and all page, the call

will be disconnected. When transferring a call, outside call will remain on hold
even in the case of a power failure, so you can return to the outside call.

Tip

If there is a power failure during an outside call, the call may be continued, but the
handset volume and speakerphone volume can not be adjusted.

Open

Battery
compartment

6F22/6LR61 9V battery
(not supplied)

9V

«
...
69
70
71
72
73
...
»

Содержание IT-M804

















































































Отзывы:

Нет отзывов

Похожие инструкции для IT-M804

Бренд: Panasonic Страницы: 252

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 115

Бренд: Panasonic Страницы: 22

GLOBARANGE BB-GT1500E

Бренд: Panasonic Страницы: 10

Бренд: Daewoo Страницы: 32

Бренд: Aastra Страницы: 2

Бренд: Aastra Страницы: 2

Бренд: Aastra Страницы: 2

Бренд: Aastra Страницы: 2

Dialog 4106 Basic

Бренд: Aastra Страницы: 2

Бренд: EastLink Страницы: 28

Бренд: Aastra Страницы: 461

Бренд: Aastra Страницы: 40

Бренд: Aastra Страницы: 47

Бренд: Aastra Страницы: 47

Бренд: Talkswitch Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды