2-7
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
2-1-5. LENS SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
201
4-422-372-01
ORNAMENT, LENS (Note 3)
202
A-1898-068-A
SERVICE,
LSV-1550A-BI
203
1-856-033-21
OPTICAL FILTERBLOCK (OFB-03-52)
204
3-216-044-01
RUBBER (1270), SEAL
205
A-1785-655-A CMOS BLOCK ASSY (1390) -077 (including IC6701
(COMS Imager)) (Note 1)
206
4-422-373-01
SHEET, CM RADIATION (Note 2)
207
4-422-356-01 FRAME,
LD
208
4-422-355-01 FRAME,
VC
209
1-885-375-11
FP-1550 FLEXIBLE BOARD
210
4-425-581-01
SHEET (A), SHIELD
211
1-885-376-11
FP-1551 FLEXIBLE BOARD
212
A-1889-556-A LD-297 BOARD, COMPLETE
213
4-422-358-01
HEAT SINK (A), VC
214
4-281-952-01
SHEET (B), VC RADIATION
#2
2-635-562-31 SCREW
(M1.7)
#3
2-660-401-01
SCREW (M1.7), NEW TRU-STAR, P2
#12
3-080-204-21 SCREW,
TAPPING,
P2
1. Remove in numerical order (
1
to
6
) in the left figure.
DISASSEMBLY
1
#3 X 1
→
#2 X 1
Top View
Right View
#3
#2
3
#3 X 1
→
#2 X 1
Front View
Right View
#2
#3
4
#3 X 3
Back View
#3
5
#3 X 6
Back View
Left View
Top View
Bottom View
#3
#3
#3
#3
Screw
#3: M1.7 X 2.5
(Red)
2-660-401-01
2.5
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
Note
Note 2:
The CM Radiation Sheet when peeling off once, so that it
cannot be reused.
Note 2:
CM Radiation Sheetは一度剥がすと粘着力が弱くなるため、
再利用はしないでください。
Refer to “Assembly-4: The Method of removing of Lens
Ornament.”.
“Assembly-4: The Method of removing of Lens Ornament.”
を参照してください。
Note 1:
Be sure to read “Precautions for Replacement of Imager” on
page 6-1 when changing the imager.
Note 1:
イメージャの交換時は6-1ページ、“イメージャ交換時の注
意”を必ずお読みください。
Refer to "Caution for Handling
the Lens Device (LSV-1550A-BI)"
#12
#3
#3
#3
#2
#3
#2
#3
#3
#3
#3
6
3
202
Cabinet (R) Section
2
213
4
212
5
208
207
204
206
(Note 2)
214
209
210
201
(Note 3)
211
203
1
Cabinet (F) Section
205
(including IC6701
(CMOS imager))
(Note 1)
2
(Bosses)
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
The changed portions from
Ver. 1.0 are shown in blue.
