Sony HXC-FB80, Руководство по эксплуатации

Страница: 30 / 71

30
For example, if one position is disabled, then that position is not
displayed and the button switches between the remaining three
positions.
4
Repeat steps 2 and 3 as required.
5
Assign the CC filter switching function (ELECTRICAL
CC) to a button on the <SWITCH ASSIGN1> page in the
OPERATION menu.
For the ASSIGN 1/2/3 buttons, select ASSIGNABLE 1/2/3 and
set to ELECTRICAL CC. For the COLOR TEMP. button,
select ASSIGN CTEMP and set to ELECTRICAL CC.
White balance memory
There are two white balance memories: A and B. When you execute
automatic white balance adjustment, the adjusted white balance
value is stored in the memory (A or B) selected with the WHITE
BAL switch.
The white balance values stored in memory are retained until the
white balance is adjusted again, including when power is turned off.
When power is turned on again, the white balance in memory
corresponding to the current WHITE BAL switch setting is loaded.
Setting the Electronic Shutter
When connected to a camera control unit or external control device (for
example, RCP or RM), the electronic shutter settings are controlled from the
connected device. They are not controlled using the camera.
For details about operations on the external control device, refer to
the operating instructions or operation manual for the device.
Shutter modes
The shutter modes that can be used with the electronic shutter and
the shutter speeds that can be selected are listed below.
Standard mode
Select this mode for shooting fast-moving subjects with little
blurring.
ECS (Extended Clear Scan) mode
Select this mode for obtaining images with no horizontal bands of
noise when shooting subjects such as monitor screens.
SLS (Slow Shutter) mode
Select this mode to shoot dimly lit subjects.
You can set the number of accumulated frames to 2, 3, 4, 5, 6, 7, or
8 frames.
In SLS mode, the following limitations apply to automatic functions.
Y: Available, N: Not available
Setting the shutter mode and shutter speed
• When automatic iris is used, the iris opens wider as the shutter speed
increases, reducing the depth of field.
• The selectable shutter speeds vary depending on the current system
frequency.
Setting the shutter mode and standard mode
shutter speed
Once the shutter speed is selected, it is retained even when the
camera power is turned off.
1
Push the SHUTTER switch from ON to SEL.
The current shutter setting indication appears in the viewfinder
for about three seconds.
Example: SHUTTER: 1/250
2
Before the shutter setting indication disappears, push the
SHUTTER switch to SEL again.
Note
System frequency Shutter speed (sec.)
• 59.94i
• 59.94P 1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000
• 50i
• 50P 1/60, 1/125, 1/250, 1/500, 1/1000, 1/2000
• 29.97PsF 1/40, 1/60, 1/100, 1/120, 1/125, 1/250, 1/500,
1/1000, 1/2000
• 25PsF 1/33, 1/50, 1/100, 1/125, 1/250, 1/500, 1/1000,
1/2000
• 23.98PsF 1/32, 1/48, 1/96, 1/100, 1/125, 1/250, 1/500,
1/1000, 1/2000
SYSTEM LINE System frequency Shutter speed (Hz)
1080 59.94i 60.00 to 4300
59.94P 59.96 to 4600
50i 50.00 to 4700
50P 50.03 to 4600
29.97PsF 30.00 to 2700
25PsF 25.00 to 2300
23.98PsF 24.00 to 2200
720 59.94P 59.96 to 4600
50P 50.03 to 4600
Note
Function Operation in SLS mode
2F 3F/4F/5F/6F/7F/8F
AUTO WHITE Y Y
AUTO BLACK Y 2F setting
AUTO WHITE SHADING N N
AUTO BLACK SHADING N N
AUTO LEVEL N N
AUTO HUE N N
AUTO IRIS Y Y
ATW Y Y
AUTO KNEE Y Y
FLARE Y Y
D.EXT Y Y
TLCS (AUTO SHUTTER) Last enabled function takes
precedence
Notes