Sony HKSR-101, Руководство по эксплуатации

Страница: 75 / 128

Cha
p
te
r
6
Memo
ry
Re
c
o
rdin
g (
W
it
h HK
SR-10
2
In
s
tall
ed)
75
6-1 Timer Rec
3
Rotate the SELECT/ENTER dial to select the number
of frames to record in one take.
4
Start recording.
In Manual Timer Rec mode, “M” appears on the
HOME screen before the number of lines of the signal
format.
After about 0.5 seconds of normal tape recording, the
specified number of frames are accumulated in the
memory of the HKSR-102. Recording to tape starts
again when the amount of data reaches the specified
amount. The tally indicator of this unit lights during
storage to memory and during recording to tape.
During Manual Timer Rec recording, each time the
PAUSE button is pressed, the specified number of
frames are accumulated in the memory and the unit is
put into recording standby mode.
To check the amount of data in memory
Press FUNC + HOME twice. The amount appears at
the bottom of the display
(see page 81) .
To cancel Manual Timer Rec mode
Press the STOP button.
Note
Do not stop recording until the amount of data in memory
exceeds 20%. When there is only a small amount of data in
memory, recording may stop without transferring the
images to tape.
6-1-2 Auto Timer Rec
Note
In the SYSTEM Setup menu, set SELECT FPS to “OFF”.
1
In the SYSTEM Setup menu, set EDIT >TIMER REC
to “AUTO”.
2
In the submenu window, select “Interval” and then
press the SELECT/ENTER dial.
A setting window opens.
3
Rotate the SELECT/ENTER dial to set the recording
interval (hours/minutes/seconds).
4
In the submenu window, select “Auto Frm” and then
press the SELECT/ENTER dial.
A setting window opens.
5
Rotate the SELECT/ENTER dial to specify the
number of frames to record in one take.
6
Put the unit into recording paused mode.
In Auto Timer Rec mode, “T” appears on the HOME
screen before the number of lines of the signal format.
Recording at the specified intervals of specified time
begins, and the specified number of frames are
accumulated in the memory of the HKSR-102.
Recording to tape starts when the amount of data
reaches the specified amount. The tally indicator of
this unit lights during storage to memory and during
recording to tape
To check the amount of data in memory
Press FUNC + HOME twice.
The amount appears at
the bottom of the display, together with information
such as the time remaining until the start of the next
recording
(see page 81) .
Note
Do not stop recording until the amount of data in memory
exceeds 20%. When there is only a small amount of data in
memory, recording may stop without transferring the
images to tape.
ANA
EMP
1
L R
ANA
EMP
2
L R
SDI
EMP
3
L R
SDI
EMP
4
L R
SDI
EMP
5
L R
SDI
EMP
6
L R
SDI
EMP
7
L R
SDI
EMP
8
L R
SDI
EMP
9
L R
SDI
EMP
10
L R
A/E
EMP
11
L R
A/E
EMP
12
L R
dB
0
-10
-20
-30
-60
TCG
REMAIN CH.COND
- - -
1080
23.98PsF
4:2:2
IN: --:--:--:--
LOCAL
EE
15:25
RECINHI
KEYINHI
00
H
00
M
00
S
00
F
PB
13.2V
SRW-1
M
ANA
EMP
1
L R
ANA
EMP
2
L R
SDI
EMP
3
L R
SDI
EMP
4
L R
SDI
EMP
5
L R
SDI
EMP
6
L R
SDI
EMP
7
L R
SDI
EMP
8
L R
SDI
EMP
9
L R
SDI
EMP
10
L R
A/E
EMP
11
L R
A/E
EMP
12
L R
dB
0
-10
-20
-30
-60
TCG
REMAIN CH.COND
- - -
1080
23.98PsF
4:2:2
IN: --:--:--:--
LOCAL
EE
15:25
RECINHI
KEYINHI
00
H
00
M
00
S
00
F
PB
13.2V
SRW-1
T