ILME-FX30
5-045-568-11(1)
\\Win-473\camera\CX96700(LAX)B_SG\JPEN\01_Compose\EN\5045568111\5045568111ILMEFX30AF1\EN1AF1.indd
DTP data saved: 2022/05/16 11:11
PDF file created: 2022/05/16 11:11
Hereby, Sony Corporation declares that this equipment is in compliance with the UK relevant
statutory requirements.
The full text of the declaration of conformity is available at the following internet address:
https://compliance.sony.co.uk
For this radio equipment the following restrictions on putting into service or of requirements for
authorization of use apply in AT/BE/BG/CY/CZ/DK/EE/FI/FR/DE/EL/HU/IE/IT/LV/LT/LU/MT/NL/
PL/PT/RO/SK/SI/ES/SE/UK/UK(NI)/HR/IS/LI/NO/CH/AL/BA/MK/MD/RS/ME/XK/TR:
5 150 - 5 350 MHz band is restricted to indoor operations only.
For Customers in Indonesia
IEEE802.11b/g/n
2 400 MHz
Bluetooth
2 400 MHz
For customers who purchased their camera from a store in
Japan that caters to tourists
Note
Some certification marks for standards supported by the camera can be confirmed on the screen
of the camera.
Select MENU
(Setup)
[Setup Option]
[Certification Logo].
Specifications
Camera
[System]
Camera Type:
Interchangeable Lens Digital Camera
Lens: Sony E-mount lens
[Image sensor]
Image format: APS-C size (23.3 mm ×
15.5 mm), CMOS image sensor
Effective pixel number of camera:
Approx. 26 000 000 pixels
Total pixel number of camera:
Approx. 27 000 000 pixels
[Monitor]
7.5 cm (3.0 type) TFT drive, touch panel
[General]
Rated input: 7.2 V
, 5.6 W (during movie
recording)
Operating temperature:
0 °C to 40 °C (32 °F to 104 °F)
Storage temperature:
–20 °C to 55 °C (–4 °F to 131 °F)
Dimensions (W/H/D) (Approx.):
129.7 × 77.8 × 84.5 mm
5 1/8 × 3 1/8 × 3 3/8 in.
Mass (Approx.):
646 g (1 lb 6.8 oz) (including battery
pack, SD card)
[Wireless LAN]
WW878474 (see name plate on the bottom
of camera)
Supported format: IEEE 802.11 a/b/g/n/ac
Frequency band: 2.4 GHz/5 GHz
Security: WEP/WPA-PSK/WPA2-PSK
Connection method:
Wi-Fi Protected Setup™ (WPS)/Manual
Access method: Infrastructure mode
WW679215 (see name plate on the bottom
of camera)
Supported format: IEEE 802.11 b/g/n
Frequency band: 2.4 GHz
Security: WEP/WPA-PSK/WPA2-PSK
Connection method:
Wi-Fi Protected Setup™ (WPS)/Manual
Access method: Infrastructure mode
XLR handle unit (ILME-FX30 only)
Mass (Approx.): 305 g (10.8 oz)
AC Adaptor
AC-UUD12/AC-UUE12/AC-UUE12 T
Rated input:
100 - 240 V
, 50/60 Hz, 0.2 A
Rated output: 5 V
, 1.5 A
Rechargeable battery pack
NP-FZ100
Rated voltage: 7.2 V
Design and specifications are subject to
change without notice.
Trademarks
•
is a trademark of Sony Group Corporation.
• USB Type-C® and USB-C® are registered trademarks of USB Implementers Forum.
• Wi-Fi, the Wi-Fi logo and Wi-Fi Protected Setup are registered trademarks or trademarks of the
Wi-Fi Alliance.
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by Sony Group Corporation and its subsidiaries is under license.
• QR Code is a trademark of Denso Wave Inc.
• In addition, system and product names used in this manual are, in general, trademarks or
registered trademarks of their respective developers or manufacturers. However, the ™ or ®
marks may not be used in all cases in this manual.
Viewing
1
Press the (Playback) button to switch
to the playback mode.
(Playback) button
Control wheel
2
Select an image with the control wheel.
You can move to the previous image/next
image by pressing the left/right side of the
control wheel.
To start playing back a movie, press the
center button on the control wheel.
Notes on use
Refer to “Precautions“ in the “Help Guide” as well.
Notes on handling the product
• This camera is designed to be dust-and moisture-resistant, but is not waterproof or dust-proof.
• Do not leave the lens exposed to a strong light source such as sunlight. Because of the lens’s
condensing function, doing so may cause smoke, fire, or a malfunction inside the camera body
or the lens. If you have to leave the camera exposed to a light source such as sunlight, attach
the lens cap to the lens.
• If sunlight or other strong light enters the camera through the lens, it may focus inside the
camera and cause smoke or fire. Attach the lens cap when storing the camera. When shooting
with backlighting, keep the sun sufficiently far away from the angle of view. Even if it is slightly
away from the angle of view, smoke or fire may still occur.
• Do not directly expose the lens to beams such as laser beams. That may damage the image
sensor and cause the camera to malfunction.
• Do not look at sunlight or a strong light source through the lens when it is detached. This may
result in unrecoverable damage to the eyes or cause a malfunction.
• This camera (including accessories) has magnet(s) which may interfere with pacemakers,
programmable shunt valves for hydrocephalus treatment, or other medical devices. Do not
place this camera close to persons who use such medical devices. Consult your doctor before
using this camera if you use any such medical device.
• Increase the volume gradually. Sudden loud noises can damage your ears. Be especially careful
when listening to headphones.
• Do not leave the camera, the supplied accessories, or memory cards within the reach of infants.
They may be accidentally swallowed. If this occurs, consult a doctor immediately.
• While the cooling fan is in operation, be careful not to let any objects get sucked into the fan.
Notes on the monitor
• The monitor is manufactured using extremely high-precision technology, and over 99.99% of
the pixels are operational for effective use. However, there may be some small black dots and/
or bright dots (white, red, blue or green in color) that constantly appear on the monitor. These
are imperfections due to the manufacturing process and do not affect the recorded images in
any way.
• If the monitor is damaged, stop using the camera immediately. The damaged parts may harm
your hands, face, etc.
Notes on continuous shooting
During continuous shooting, the monitor may flash between the shooting screen and a black
screen. If you keep watching the screen in this situation, you may experience uncomfortable
symptoms such as feeling of unwellness. If you experience uncomfortable symptoms, stop using
the camera, and consult your doctor as necessary.
Notes on recording for long periods of time or recording 4K movies
• The camera body and battery may become warm with use – this is normal.
• If the same part of your skin touches the camera for a long period of time while using the
camera, even if the camera does not feel hot to you, it may cause symptoms of a low-
temperature burn such as redness or blistering. Pay special attention in the following situations
and use a tripod, etc.
- When using the camera in a high temperature environment
- When someone with poor circulation or impaired skin sensation uses the camera
- When using the camera with [Auto Power OFF Temp.] set to [High]
• Do not touch the area around the ventilation outlet for long periods of time. Doing so may
cause low-temperature burns.
Notes on using memory cards
• When recording is finished, the memory card may become hot. This is not a malfunction.
• If
(overheating warning icon) is displayed on the monitor, do not remove the memory card
from the camera right away. Instead, wait for a while after turning off the camera, and then
remove the memory card. If you touch the memory card while it is hot, you may drop it and the
memory card may be damaged. Be careful when removing the memory card.
Notes on using a tripod
Use a tripod with a screw less than 5.5 mm (7/32 inches) long. Otherwise, you cannot firmly
secure the camera, and damage to the camera may occur.
Notes on the XLR handle unit (supplied) (ILME-FX30 only)
• Before connecting/disconnecting an external microphone or device to/from the INPUT1 or
INPUT2 jack, be sure to set the INPUT1 (LINE/MIC/MIC+48V) or INPUT2 (LINE/MIC/MIC+48V)
switch to a position other than “MIC+48V.” Plugging/unplugging the cable into/from the
external microphone or device while the switch is set to “MIC+48V” may cause loud noise or a
malfunction of the device.
• While recording is in progress, operating and handling noises from the camera or lens may be
recorded. Touching the handle while recording is in progress will cause noise to be included in
the recording.
• While recording is in progress, do not change the INPUT1 or INPUT2 switch settings.
• If the microphone of the handle is in proximity to a speaker, acoustic feedback may occur. In
this case, move the handle away from the speaker to allow the maximum distance between the
microphone and the speaker, or lower the speaker volume.
• If dust or water droplets are present on the surface of the microphone, successful recording
may not be possible. Be sure to clean the microphone surface before using the handle.
• Turn off the camera before attaching/removing the handle.
• When the handle is connected to the camera and the HANDLE AUDIO ON/OFF switch is set to
ON, the internal microphone of the camera cannot record audio input.
• When attaching the handle to the camera, fasten the two handle-attachment screws securely.
Using the handle without fastening the handle-attachment screws may damage the Multi
Interface Shoe terminal or cause the handle to fall off.
Sony lenses/accessories
Using this unit with products from other manufacturers may affect its performance, leading to
accidents or malfunction.
Warning on copyrights
Television programs, films, videotapes, and other materials may be copyrighted. Unauthorized
recording of such materials may be contrary to the provisions of the copyright laws.
Notes on location information
If you upload and share still images or movies taken with this camera on the Internet while the
location information is linked with the dedicated smartphone application, you may accidentally
reveal the location information to a third party. To prevent third parties from obtaining your
location information, deactivate the [Location Information Linkage] function of the dedicated
application.
Notes on discarding or transferring this product to others
Before discarding or transferring this product to others, be sure to perform the following
operation to protect private information.
• Select [Setting Reset]
[Initialize].
Notes on discarding or transferring a memory card to others
Executing [Format] or [Delete] on the camera or a computer may not completely delete the data
on the memory card. Before transferring a memory card to others, we recommend that you
delete the data completely using data deletion software. When discarding a memory card, we
recommend that you physically destroy it.
Note on network functions
When you use network functions, unintended third parties on the network may access the
camera, depending on the usage environment. For example, unauthorized access to the camera
may occur in network environments to which another network device is connected or can
connect without permission. Sony bears no responsibility for any loss or damage caused by
connecting to such network environments.
Note on the 5 GHz band for wireless LAN
When using the wireless LAN function outdoors, set the band to 2.4 GHz by following the
procedure below. (WW878474 only)
• MENU
(Network)
[Wi-Fi]
[Wi-Fi Frequency Band]
How to turn off wireless network functions (Wi-Fi, etc.) temporarily
When you board an airplane, etc., you can turn off all wireless network functions temporarily
using [Airplane Mode].
Power Cord
Multiple power cords may be supplied with this
equipment. Use the appropriate one that matches
your country/region.
For the customers in the UK, Ireland, Malta, Cyprus
and Saudi Arabia
Use the power cord (A).
For safety reasons, the power cord (B) is not intended
for above countries/regions and shall therefore not
be used there.
For the customers in other EU countries/regions
Use the power cord (B).
(A)
(B)
For Customers in the U.S.A. and Canada
The available scientific evidence does not show that any health problems are associated with
using low power wireless devices. There is no proof, however, that these low power wireless
devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency
energy (RF) in the microwave range while being used.
Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF
that does not produce heating effects causes no known adverse health effects. Many studies of
low-level RF exposures have not found any biological effects. Some studies have suggested that
some biological effects might occur, but such findings have not been confirmed by additional
research. This equipment has been tested and found to comply with FCC/ISED radiation exposure
limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules.
For Customers in the U.S.A.
For question regarding your product or for the Sony Service Center nearest you, call 1-800-222-
SONY (7669) .
Supplier’s Declaration of Conformity
Trade Name : SONY
Model : WW878474
Responsible Party : Sony Electronics Inc.
Address : 16535 Via Esprillo, San Diego, CA 92127 U.S.A.
Telephone Number : 858-942-2230
Important note on use of 5 GHz wireless LAN
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down through the MAC,
through the digital and analog baseband, and finally to the RF chip. Several special packets are
initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF
transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on
only while one of the aforementioned packets is being transmitted. In other words, this device
automatically discontinue transmission in case of either absence of information to transmit or
operational failure.
Frequency Tolerance: ±20 ppm
For Customers in Canada
5 150-5 350 MHz band is restricted to indoor operation only.
High-power radars are allocated as primary users (i.e. priority users) of the bands 5 250-
5 350 MHz and 5 650-5 850 MHz and that these radars could cause interference and/or damage
to LE-LAN devices.
For Customers in Europe
IEEE802.11b/g/n
2 400 MHz
< 60 mW e.i.r.p.
IEEE802.11a/n/ac
5 150-5 350 MHz
5 470-5 725 MHz
< 35 mW e.i.r.p.
IEEE802.11a/n/ac
5 725-5 850 MHz
< 25 mW e.i.r.p.
Bluetooth
2 400 MHz
< 10 mW e.i.r.p.
Hereby, Sony Corporation declares that this equipment is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
https://www.compliance.sony.eu
Additional information on this product and answers to frequently asked questions can be
found at our Customer Support Website.