1-3
HDR-CX530E/CX535/CX610E/PJ530E/PJ540/PJ540E/PJ610E_L2
– ENGLISH –
1-6. METHOD OF COPING WITH SHIFT LENS ERROR
VC-1025 BOARD (SIDE A)
C6814 C6815
C6816 C6817
R1401
IC6800
Fig. 1
Measurement points on the VC-1025 board
approx. 330 msec
Note:
The length of low section will vary a little depending on the conditions.
Fig. 2
Change in output voltage of R1401 on the VC-1025 board
Note 3:
When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
E
6
1
1
1
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
E
6
1
3
0
Reset position detection error on the
stepper iris initializing
Turn the power on to open lens barrier. Disconnect the battery or power
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive
block (pin
wl
,
ek
of CN4001 on the VC-1025 board).
If iris blades work normally, confirm that they are closing completely
and confirm following item.
• Case of the iris blades do not close normally. Replace the lens block.
• Case of “E: 61: 30” is appeared and iris blades closed completely.
Confirm that communication with lens block is normal.
• Case of LCD is not displayed normally. Check that connection between
CN6702 on CM-1004 board and CN4004 on VC-1025 board by FP-
2189 flexible board.
• Case of LCD is displayed normally. Replace the lens block.
E
6
2
0
0
Handshake correction function does not
work well. (With PITCH angular veloc-
ity sensor output stopped.)
Inspect PITCH angular velocity sensors (SE7701 on the JK-1009
board) peripheral circuits.
E
6
2
0
1
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
Inspect YAW angular velocity sensors (SE7701 on the JK-1009 board)
peripheral circuits.
E
6
2
0
2
Abnormality of IC for steadyshot.
Refer to “1-6-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Oc-
curred”.
E
6
2
0
3
IC for steadyshot and micro controller
communication abnormality among.
Inspect the steadyshot circuit (IC7711 on the VC-1025 board).
E
6
2
0
4
Image vibration correction during hand-
shake function does not work.
Inspect the image vibration angular velocity sensors (SE7711 on the
VC-1025 board) peripheral circuits.
E
6
2
1
0
Shift lens initializing failure.
Replacement of lens block (Note 3).
If an error occurs again, replace the VC-1025 board.
E
6
2
1
1
Shift lens overheating (Pitch)
Refer to “1-6-2. E : 62 : 11 (Shift Lens Overheating (Pitch)) Occurred”.
E
6
2
1
2
Shift lens overheating (Yaw)
Refer to “1-6-3. E : 62 : 12 (Shift Lens Overheating (Yaw)) Occurred”.
E
6
2
2
0
Abnormality of thermistor.
Refer to “1-6-4. E : 62 : 20 (Abnormality of Thermistor) Occurred”.
E
6
2
3
0
Abnormal CPU
Turn power off and turn power on again.
E
9
1
0
1
Abnormality when flash is being
charged.
Turn power off and turn power on again.
E
9
1
0
2
Abnormality of LED Video light.
Turn power off and turn power on again.
E
9
1
0
3
Abnormality of LED Video light Tem-
perature detection.
Turn power off and turn power on again.
E
9
2
0
1
Battery current value goes over the max
discharge current
Check the remaining battery power because this symptom maybe de-
pended on the remaining battery level, and confirm whether or not the
symptom is occurred after replacing the battery. If the symptom is still
occurred, overhaul inspection is needed. Check each output of DC/
DC converter (IC5100 on the VC-1025 board) with connected the DC
JACK (CN4007) on the VC-1025 board.
(The minimum connection to periphery)
E
9
4
0
0
Fault of writing or erasing the flash
memory
CX535/PJ530E/PJ540/PJ540E:
Inspect the flash memory (IC8101 on the MM-102 board).
CX610E/PJ610E:
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
E
9
4
0
1
Internal flash memory fault
CX535/PJ530E/PJ540/PJ540E:
Inspect the flash memory (IC8101 on the MM-102 board).
CX610E/PJ610E:
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).
E
9
4
0
2
BGM data error
Check the CPU (IC6000 on the VC-1025 board).
E
9
5
0
0
GPS hardware error
Turn power off and turn power on again.
E
9
6
0
0
Map area mount error
Turn power off and turn power on again.
E
9
7
0
0
Projector hardware error
Turn power off and turn power on again.
*
*
