34
Pin No.
Pin Name
I/O
Description
47
D/A.RESET
O
Reset signal output to the D/A converter (IC601) “L”: reset
48
SCK
I
Serial data transfer clock signal input from the SONY bus interface (IC302)
49
SI
I
Serial data input from the SONY bus interface (IC302)
50
SO
O
Serial data output to the SONY bus interface (IC302)
51
SCLK
O
Subcode Q data reading clock signal output to the CXD2530Q (IC101)
52
SUBQ
I
Subcode Q data input from the CXD2530Q (IC101)
53
—
O
Not used (open)
54
C.OUT
I
Track number count signal input from the CXA1992BR (IC11)
55
BUS.ON
I
Bus on/off control signal input from the SONY bus interface (IC302) “H”: bus on
56
A/D.SW
I
Analog/digital select switch (SW801) input terminal “L”: digital, “H”: analog
57
MGLK
I
Magazine eject operation completion detect switch (SW201) input “L”: magazine detected
58
ELV.F
O
Motor drive signal (elevator up direction) output to the elevator motor drive (IC301)
“L” active *2
59
—
O
Not used (open)
60
MAG.SW
I
Magazine in/out detect switch (SW202) input “L”: normally “H”: magazine in/out operation
61
BU.CHK
I
Battery detection signal input terminal “H”: battery on
62
W.UP
I
Bus on or eject switch (SW301) input terminal “H”: bus on or eject switch pushing
63
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2530Q (IC101)
64
EJECT
I
Eject switch (SW301) input terminal “H” active
65
CD.CLK
O
Serial data transfer clock signal output to the CXD2530Q (IC101) and CXD2522Q (IC401)
66
CD.XLT
O
Serial data latch pulse signal output to the CXD2530Q (IC101)
67
CD.DATA
O
Serial data output to the CXD2530Q (IC101) and CXD2522Q (IC401)
68
CD.ON
O
D/A converter and servo section power supply on/off control signal output “H”: power on
69
ELV.ON
O
Mechanism deck section power supply on/off control signal output “H”: power on
70
ELV.R
O
Motor drive signal (elevator down direction) output to the elevator motor drive (IC301)
“L” active *2
71
—
O
Not used (open)
72
VDD
—
Power supply terminal (+5V)
73
NC (VDD)
—
Connected to the power supply (+5V)
74
BUSY
I
Busy monitor input from the CD text decoder (IC501) “L”: busy status
75
RESET
O
Reset signal output to the CD text decoder (IC501) “L”: reset
76
REQ
I
Data request signal input from the CD text decoder (IC501) “L” active
77
CCCLK
O
Command clock signal output to the CD text decoder (IC501)
78
CSO
O
Command data output to the CD text decoder (IC501)
79
CSI
I
Command data input from the CD text decoder (IC501)
80
ADJ
I
Automatic/manual adjustment selection terminal
“L”: manual adjustment mode, “H”: automatic adjustment mode (fixed at “H” in this set)
*1 chucking motor (M103) control
STOP
LOAD
CHUCKING
SAVE
BRAKE
CH.F (pin
4
)
“H”
“L”
“H”
“L”
CH.R (pin
5
)
“H”
“H”
“L”
“L”
Mode
Terminal
*2 elevator motor (M104) control
STOP
ELEVATOR
UP
ELEVATOR
DOWN
BRAKE
ELV.F (pin
tk
)
“H”
“L”
“H”
“L”
ELV.R (pin
u;
)
“H”
“H”
“L”
“L”
Mode
Terminal
Содержание CDX-838 - Compact Disc Changer System
Страница 3: ...3 SECTION 2 GENERAL This section is extracted from instruction manual ...
Страница 4: ...4 ...
Страница 5: ...5 ...
Страница 29: ...29 29 CDX 838 7 13 SCHEMATIC DIAGRAM DIGITAL OUT JACK Boards Page 25 ...
