Sony BRS-200 Скачать руководство пользователя страница 40

Страница: 40 / 159

Installation and Connection of the Switcher

Ch
apt

er 3 Prep

ion
s

Installation and Connection of the Switcher

This section describes installation and connection of the switcher.

Installing an Interface Board

Install an optional interface board in the card slot at the rear of the Processor
Unit. The Processor Unit has three card slots at the rear. Some of the interface
boards are restricted with regard to installation in some of these three card slots.

Interface boards and available card slots

Yes: can be installed, No: cannot be installed

To install an interface board

• Be sure to turn off all the equipment before attaching or removing an interface

board.

•

Immediately after the switcher has been turned off, the Processor Unit is
hot.

Be sure to wait more than 30 minutes after the switcher is turned off

before you open the top cover of the Processor Unit.

• Do not remove any panels inside other than the top panel of the Processor

Unit.

• Be sure to use the attachment screws supplied with an interface board to install

it in the card slot. Using other screws may cause damage to the interface board
and the Processor Unit.

• When installing the interface board, be careful not to injure yourself.

Interface board

Card slot

IN1

IN2

OUT

BRSA-20HSD1 HD/SD-SDI
input board

Yes

BRSA-20DD1 DVI input
board

Yes

BRSA-20DD2 DVI output
board

Yes

PGM1

PGM2

AUX1

SDI OUT

SDI IN

AUX2

REF IN

REF OUT

RS-232C

AC IN

RS-422

DVI-I OUT

GENLOCK

VISCA

GPI I/O

PANEL

LAN(10/100)

REMOTE

IN1

IN2

OUT

IN1 card slot

IN2 card slot

OUT card slot

Notes

Содержание BRS-200
































































































































































Результаты поиска

Содержание BRS-200

Отзывы:

Похожие инструкции для BRS-200

Бренды по названию

Популярные бренды

Sony BRS-200, Руководство по эксплуатации

Результаты поиска

Содержание BRS-200

Отзывы:

Похожие инструкции для BRS-200

Бренды по названию

Популярные бренды