background image

SERVICE MANUAL (COMMON) 

ORIGINAL MANUAL ISSUE DATE:  2019.01

 

Conditions of Use: 
(1)  Please  use  this  information  only  for  the  purpose  of  performing  repair,  maintenance  and/or  configuration  services  of  the  Sony  products 

(hereinafter  the 

“Repair  services”)  under  the  service  agreement  entered  into  with  the  Sony  group  company  (hereinafter  the  “Service 

agreement”). Using this information for any purpose other than the purpose described foregoing is forbidden. 

(2) Only the Authorized 

Servicer’s officers, employees or subcontractors (including their officers and employees) whose duties justify a need-to-

know and who have agreed to hold confidential this information (collectively hereinafter the 

”Permitted users”) are permitted to access and 

use this information.  To disclose or disseminate to any person other than the Permitted users  is forbidden. 

(3)  Destroy  or  erase  any  and  all  portion  of  this  information  promptly  in  an  irrecoverable  and  secure  fashion  after  achieving  the  purpose 

described in Section (1) above. 

(4)  Do  not  copy,  replicate,  reproduce,  alter,  translate,  transmit,  sell,  lease,  or  distribute  this  information  in  whole  or  in  part  without  the  prior 

written permission of the author. 

     (Notwithstanding foregoing, it is permitted to copy and distribute this information to the Permitted users.) 
(5) Please notify immediately any leakage, loss, theft, misappropriation, or other misuse of this information by e-mail to the following address: 
 

[email protected] 

(6) In addition to the above, the terms and conditions of the Service agreement shall be applied to using this information. 
 
Revision of Information: 
This  information  may  be  changed  or  updated  at  any  time  without  any  prior  notice.  Please  confirm  that  this  information  is  up-to-date  before 
using it. 

9-888-763-01 

 

LCD TV 

 
 
 
 

Sony EMCS (M) Sdn. Bhd., SVPM 

 

     © 2019.01 

GN5UN CHASSIS 

Segment : SV 

(See next page for revision )

 

SYS SET

2019/01/30 02:46:26 (GMT+09:00)

Содержание Bravia KDL-43WG6 Series
























































































































































Отзывы: