manualshive.com logo in svg

Sony Ericsson W550c, Руководство по эксплуатации, механическое


Поделиться
Скачать
background image

 
 
 
 
 

Working Instruction

, 

Mechanical

 

 

3/00021-1/FEA 209 544/594 B 

©

 Sony Ericsson Mobile Communications AB 

108(128) 

 

Step-by-Step Instructions 

8.

 

Verify that the microphone grommet is installed over 
the microphone. 

9.

 

Using the two alignment features associated with this 
switch, place the camera switch portion of the display 
flex film into its position on the side of the display 
carrier.  

•

 

Perform sections 3.2.1 - 3.2.4 of the Flip Reassembly Procedure 

•

 

Perform sections 2.2.2 - 2.2.4 the Base Reassembly procedure. 

 

 

4.33

 

Microphone 

This part comes as part of the display flex film assembly.  Therefore to replace this part, the 
entire display flex film assembly must be replaced.  Refer to the “Display Flex Film Assembly 
and the Display Carrier” section for the instructions on replacing the display flex film assembly. 

 

Содержание W550c

































































































































Отзывы:

Нет отзывов

Похожие инструкции для W550c

Yealink W56P Telesystem Quick Start Manual preview
W56P Telesystem
Бренд: Yealink Страницы: 12
Yealink Verizon One Talk W60B Quick Reference Manual preview
Verizon One Talk W60B
Бренд: Yealink Страницы: 8
Yealink Telkom W52P Specification preview
Telkom W52P
Бренд: Yealink Страницы: 2
Yealink T46S Skype for Business Handling Instruction preview
T46S Skype for Business
Бренд: Yealink Страницы: 2
Yealink VP59 Teams Administrator'S Manual preview
VP59 Teams
Бренд: Yealink Страницы: 533
Logitech POWERSHELL Setup Manual preview
POWERSHELL
Бренд: Logitech Страницы: 152
Tyco 3G4010 v4.0 Installation Manual preview
3G4010 v4.0
Бренд: Tyco Страницы: 36
Sagem MYC-3 Technical Documentation Manual preview
MYC-3
Бренд: Sagem Страницы: 105
2N StarPoint 500 Entry User Manual preview
StarPoint 500 Entry
Бренд: 2N Страницы: 59
Yealink W56B Quick Start Manual preview
W56B
Бренд: Yealink Страницы: 12
M4 SS4458 Quick Start Manual preview
SS4458
Бренд: M4 Страницы: 13
Alcatel 2057 Series User Manual preview
2057 Series
Бренд: Alcatel Страницы: 27
PSC Falcon 510 User Manual preview
Falcon 510
Бренд: PSC Страницы: 32
FLY F350s User Manual preview
F350s
Бренд: FLY Страницы: 48
iDROID IKON Z5 User Manual preview
IKON Z5
Бренд: iDROID Страницы: 21
M4 SS4045 Quick Start Manual preview
SS4045
Бренд: M4 Страницы: 22
Alcatel ONE TOUCH 993 Useful Hints & Tips preview
ONE TOUCH 993
Бренд: Alcatel Страницы: 6
SoftBank X02HT Usage Notice preview
X02HT
Бренд: SoftBank Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды