manualshive.com logo in svg

SONIX SN32F107, Руководство пользователя

Поделиться
Скачать
SONIX SN32F107 Скачать руководство пользователя страница 133

                                                                                                                        SN32F100  Series 

32-Bit  Cortex-M0  Micro-Controller

 

SONiX TECHNOLOGY CO., LTD

                           

Page 133

                                                  Version 1.9

 

 

Bit 

Name 

Description 

Attribute 

Reset 

31:9 

Reserved 

 

R 

0 

8 

OVER8 

Oversampling value 
0: Oversampling by 16 
1: Oversampling by 8

 

R/W 

0 

7:4 

MULVAL[3:0] 

Baud rate pre-scaler multiplier value = MULVAL[3:0] +1 
0000: Baud rate pre-scaler multiplier value is 1 for HW 
0001: Baud rate pre-scaler multiplier value is 2 for HW 
… 
… 
1111: Baud rate pre-scaler multiplier value is 16 for HW. 

R/W 

0 

3:0 

DIVADDVAL[3:0] 

Baud  rate  generation  pre-scaler  divisor  value.  If  this  field  is  0,  fractional 
baud rate generator will not impact the UART baud rate 

R/W 

0 

 

12.7.13 UART n Control register (UARTn_CTRL) (n=0, 1) 

Address Offset: 0x30 
 
In addition to HW flow control, this register enables implementation of SW flow control. 
 
When  TXEN  =  1,  the  UART  transmitter  will  keep  sending  data  as  long  as  they  are  available.  As  soon  as  TXEN  bit 
becomes 0, UART transmission will stop. 
 
It  is  strongly  suggested  to  let  the  UART  HW  implemented  auto  flow  control  features  take  care  of  limit  the  scope  of 
TXEN to SW flow control. 

 

 

 

Note: It is advised that TXEN and RXEN are set in the same instruction if needed in order to minimize the 

 

setup and the hold time of the receiver.

 

 

 

Bit 

Name 

Description 

Attribute 

Reset 

31:8 

Reserved 

 

R 

0 

7 

TXEN 

When this bit is 1, data written to the UARTn_TH register is output on the 
TXD pin as soon as any preceding data has been sent. 
If this bit is cleared to 0 while a character is being sent, the transmission 
of that character is completed, but no further characters are sent until this 
bit is set again. 
In  other  words,  a  0  in  this  bit  blocks  the  transfer  of  characters  from  the 
UARTn_TH register or TX FIFO into the transmit shift register. 

R/W 

1 

6 

RXEN 

0: Disable RX related function 
1: Enable RX 

R/W 

1 

5:1 

Reserved 

 

R 

0 

0 

UARTEN 

UART enable 
0: Disable . All UART shared pins act as GPIO. 
1: Enable. HW switches GPIO to UART pin automatically. 

R/W 

0 

 
 

12.7.14 UART n Half-duplex Enable register (UARTn_HDEN) (n=0, 1) 

Address Offset: 0x34 
 
After reset the UART will be in full-duplex mode, meaning that both TX and RX work independently.  After setting the 
HDEN bit, the UART will be in half-duplex mode. In this mode, the UART ensures that the receiver is locked when idle, 
or  will  enter  a  locked  state  after  having  received  a  complete  ongoing  character  reception.  Line  conflicts  must  be 
handled in SW.   
 
The behavior  of the  UART is  unpredictable  when data is presented for reception  while  data  is being transmitted. For 
this reason, the value of the HDEN register should not be modified while sending or receiving data, or data may be lost 
or corrupted. 

 

 

Содержание SN32F107

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды