HA360SA / HA360SA2.1 – Security Alert Signaler
The HA360SA / SA2.1 Security Alert will alert you to
ONE
of
several types of alerts when linked to the HA360 Main unit.
The Main unit receives a wireless signal from the HA360SA /
SA2.1 and will flash a strobe, make a loud sound and vibrate a
bed shaker. Once the Main unit receives the signal it will also
send a signal to all HomeAware remote receivers.
The HA360SA / SA2.1 has 5 different door alerts (DOOR,
FTDOOR, BKDOOR, DOOR3, DOOR4), a burglar help alert
(HELP) and a motion alert (MOTION). The unit can connect to
a NOAA weather radio (STORM), a home security (SECURIT).
Every home security system is different, contact your
provider for setup.
Installing Batteries
The HA360SA / SA2.1 Security Alert comes with two #357
silver oxide long lasting batteries that need to be installed
into the bottom of the unit. Once installed the red light
should light when the button is pushed. If the light does not
show, you may have the batteries in backwards.
NOTE:
The life expectancy for these batteries is typically
about 2 years. Only replace the batteries with #357 silver
oxide batteries. Do not use alkaline batteries.
Linking the HA360SA / SA2.1 to the Main Unit
This procedure will link your HA360SA / SA2.1 Security Alert
to your HomeAware™ Main unit. The Main unit will also
provide an alert to all HomeAware™ remote receivers. It is
best to do the LINK procedure in the same room as close as
possible to the HomeAware™ Main unit.
To link the unit to your HomeAware™ Main unit follow the
steps below.
1.
Press SET UP button on the Main unit and the word LINK
will be shown on the display, press Enter.
2.
LINK will begin blinking.
3.
Remove the cover on the bottom of the HA360SA / SA2.1
and press and release the small black link button.
4.
PICK DEVICE will display on the screen.
5.
Repeatedly pressing the blue TONE button will allow you
to select the alert you want displayed.
6.
Press ENTER.
7.
Once you have made your selection DONE will flash on
the screen.
NOTE:
There are two different versions of the HA360SA. The
only difference in their operation is the position of the
function selector switch.
HA360SA / SA2.1 Switch Locations and Positions
HA360SA
– located on the bottom of the unit next to the link
button
HA360SA2.1
– located on the back of the unit
There are three switch positions on the HA360SA and the
HA360SA2.1., right to left
1.
N.Closed
Normally closed* - Is a contact that flows current in its
normal state. Switching it on will open the contact,
causing it to not allow current flow.
NOTE:
The normally closed position is used with external
equipment that have normal closed outputs. This is
typical of burglar alarm systems.
2.
N.Open
Normally open* - Is a contact that does not flow current
in its normal state. Switching it on will close the contact,
causing it to allow current flow.
NOTE:
The normally open position is used with external
equipment that have normally open out. This typical of
weather radios.
3.
Door Chime
Is for when the barrel port is connected to the solenoid
contacts of a door chime ringer. See note below.
NOTE:
It is important that the switch not be on the open
or closed positions if the unit is being connected to the
door chime ringer. That could damage the unit if left this
way for a long period of time.
WARNING: DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE TO PREVENT DAMAGE TO UNIT.
∗
Please check the user guide of the device you are
connecting to the HA360SA / SA2.1 for the correct
switch position.
For additional information on all HomeAware products
please visit www.sonicalert.com.
