SOMMER SPA-2 Скачать руководство пользователя страница 105

Страница: 105 / 111

F-I-C

Output protocol (OP)

The type of the serial output protocol. The following options are available:

Option

Description

Sommer (default)

Sommer protocol; data values are returned with an index starting at 1

Standard

Standard protocol; data values are returned without an index

MODBUS

Modbus protocol

NOTE

For MODBUS applications run

MODBUS, set default

to get the appro-

priate communication settings.

F-I-D

OP, measurement output

Specifies the timing of the serial data output.

Option

Description

just per command

The output is only requested by commands via the RS-485 or SDI-12
interface.

measured values push

Data are returned automatically after each measurement.

F-I-E

OP, information

The main measurement values are always included in the data output string. Additionally, special
and analysis values can be included.

Option

Description

main values

Only the main values are returned.

& special values (default)

Main values and special values are returned.

& analysis values

Main, special and analysis values are returned.

Manual

105

Содержание SPA-2















































































































Результаты поиска

Содержание SPA-2

Отзывы:

Похожие инструкции для SPA-2

Бренды по названию

Популярные бренды

SOMMER SPA-2, Руководство пользователя

Результаты поиска

Содержание SPA-2

Отзывы:

Похожие инструкции для SPA-2

Бренды по названию

Популярные бренды