2
Copyright © 2014 SOMFY ACTIVITES SA. All rights reserved.
EN
Rollixo io
1.3 Caution - Important safety instructions
DANGER
The drive must be installed and adjusted by a professional
motorisation and home automation installer, in compliance
with the regulations of the country in which it is to be used.
To meet the requirements of standards EN 13241-1,
Failure to follow these instructions may result in serious
injury, e.g. due to crushing by the gate.
WARNING
Caution - Important safety instructions
For reasons of personal safety, it is important to follow
all the instructions, as incorrect installation can lead to
serious injury. Retain these instructions.
The installer must train all users to ensure the drive is
used in complete safety, in accordance with the operating
manual.
The user manual and installation manual must be given to
the end user. The installer must explain clearly to the end
user that installation, adjustment and maintenance of the
drive must be performed by a professional motorisation
and home automation installer.
1.4 Preliminary checks
> Installation environment
ATTENTION
Do not spray water onto the drive.
Do not install the drive in an explosive environment.
Check that the temperature range marked on the drive is
suited to the installation location.
> Condition of the door to be motorised
See the safety instructions for the RDO CSI motor.
1.5 Electrical pre-equipment
DANGER
The installation of the power supply must comply with
the standards in force in the country in which the drive is
LQVWDOOHGDQGPXVWEHFDUULHGRXWE\TXDOL¿HGSHUVRQQHO
The electric line must be exclusively reserved for the drive
and equipped with protection, comprising:
- a 10 A fuse or breaker,
- a differential type device (30 mA).
An all-pole power supply cut-off device must be provided.
,W LV UHFRPPHQGHG WKDW \RX ¿W D OLJKWQLQJ FRQGXFWRU
(maximum residual voltage 2 kV).
> Cable feed
Underground cables must be equipped with a protective
VKHDWKZLWKDVXI¿FLHQWGLDPHWHUWRFRQWDLQWKHPRWRUFDEOH
and the accessories cables.
For overground cables, use a cable grommet that will
withstand the weight of vehicles (ref. 2400484).
1.6 Safety instructions relating to installation
DANGER
Do not connect the drive to a power source before
installation is complete.
WARNING
Ensure that any danger zones (crushing, cutting, trapping)
EHWZHHQWKHGULYHQSDUWDQGWKHVXUURXQGLQJ¿[HGHOHPHQWV
caused by the opening movement of the driven part are
avoided or indicated on the installation (see the section on
risk prevention).
WARNING
Modifying one of the elements provided in this kit or using
an additional element not recommended in this manual is
strictly prohibited.
Monitor the door as it moves and keep people away from it
until installation is complete.
Do not use adhesive to secure the drive.
ATTENTION
,QVWDOODQ\¿[HGFRQWUROGHYLFHDWDKHLJKWRIOHVVWKDQ
m and within sight of the door, but away from moving parts.
After installation, ensure that:
- the mechanism is correctly adjusted
- the drive changes direction when the door encounters an
object 50 mm high on the ground.
WARNING
CAUTION: Automatic door – The door may operate
unexpectedly. Do not leave anything in the door's path.
> Safety devices
DANGER
A fall protection device suited to the weight of the door
must be installed to prevent the risk of the door falling.
WARNING
For operation in automatic mode or remote control,
photoelectric cells must be installed.
The automatic drive operates in at least one direction with
no intentional activation by the user.
WARNING
For operation by pressing and holding down the button
following a fault with the safety device, the door must be
operated within sight of the door.
For operation in automatic mode, or if the garage door faces
a public road, an orange light type signalling device may be
required to comply with the regulations in the country in
which the drive is installed.
