DecoFlex Keypad
Instructions
DECOFLEX WIREFREE™ RTS (Ref: 1others)
DECOFLEX™ DIGITAL WALL SWITCHES SDN (Ref: 1others)
DECOFLEX™ DIGITAL WALL SWITCHES SDN GROUP CONTROL (Ref: 1811749, 1811750)
DECOFLEX™ DIGITAL WALL SWITCHES ANIMEO® IP (Ref: 1others)
DECOFLEX DRY CONTACT KEYPAD for IGC 4n1 Motor Controller (Ref: 1811402)
ASSEMBLY
ASSEMBLE MULTIPLE BUTTON SWITCHES
Begin with a standard (assembled) 1 or 5 control button DecoFlex switch. Using
a small flat blade screw driver, carefully separate the SWITCH BASE ASSEMBLY
from the FACEPLATE (as shown in figure 1).
Add or remove CONTROL BUTTONS (as required) from the SWITCH BASE ASSEMBLY
(as shown in figure 2). Be certain the SWITCH BASE ASSEMBLY remains intact.
Attach new multiple button face plate (as shown in figure 3 & 4).
1
2
3
Applies to the following keypads:
Figure 1.
Figure 3.
Figure 2.
Figure 4.
5 Channel DecoFlex Wall Switch (Exploded view)
Removable Channel
Buttons
Switch Base
Assembly
Wall Plate
8 Button
Faceplate
REPLACE STANDARD CONTROL BUTTONS
Using a small flat blade screw driver, carefully separate the SWITCH BASE
ASSEMBLY from the FACEPLATE (as shown in figure 1).
Replace standard (blank) or temporary labeled CONTROL BUTTON(s) with
new printed CONTROL BUTTON(s).
Attach new CONTROL BUTTON FACE PLATE (as shown in figure 3 & 4).
1
2
3
5 Button
Switch Assembly
6 Button
Switch Assembly
7 Button
Switch Assembly
Battery Replacement: (RTS only)
The DecoFlex WireFree™ RTS switch is designed to provide years of maintenance
free performance. Should the battery become discharged, the LED indicator lights
will no longer function when the channel button is selected or an Up/Stop/Down
command is activated. As a result, the radio signal will be reduced or not
communicated to the RTS receiver or motor.
The battery can be easily replaced by exposing the SWITCH BASE ASSEMBLY board of the
DecoFlex WireFree™ switch. Simply slide the battery out of its holder and replace with a
new 3V Lithium battery (type 2450) maintaining the correct polarity.
NOTE:
Batteries should be disposed of properly according to local regulations.
RTS
Assembly/Installation/Operating Instructions
SDN Cable Pinout: (RJ45 connector)
ANSI/TIA/EIA 568-B Standard
Keypad RJ45 Pinout:
SDN, animeo IP and Dry Contact
CAT-5e or higher TIA-568B standard with RJ-45
Pin #
Color
SDN & animeo IP
Function
Dry Contact
Function
1
Orange White
SDN RS485 ( + )
IP1
2
Orange
SDN RS485 ( - )
IP2
3
Green White
Reserved
IP3
4
Blue
Power 24v DC ( + )
12V+
5
Blue White
Power 24v DC ( - )
N/A
6
Green
Reserved
Down
7
Brown White
SDN RS485 Ground
Up
8
Brown
SDN RS485 Ground
Ground
KEYPAD PROGRAMMING
Download and install Programming Software from this link.
https://www.somfysystems.com/support/tools/configuration-tools-software
RTS:
Follow our RTS Pocket Programming Guide to setup DecoFlex RTS keypads
Dry Contact:
Arrange switch for control in IGC 4n1 Motor Controller
*Before installing keypads all motors must be wired to the controller, have limits set and be working properly.
SDN:
The DecoFlex Digital Keypads for SDN has programmable buttons which can be
configured to control any motor or group using the SDN Keypad Programming Guide and
SDN Keypad Configuration Software. Once a keypad is fully configured, all of the settings
can be exported to a file for backup.
animeo® IP:
Keypads are configured within the animeo® IP commissioning software after
installation on the SDN bus. Use animeo® IP Visual Configuration software.
POWERING DECOFLEX KEYPADS
