Solwise WL-STATION-N2 Скачать руководство пользователя страница 32

Страница: 32 / 39

◆

Subnet Mask

— The subnet mask of OUTDOOR AP/CPE on the local area network

◆

DHCP Server

— The DHCP Server is to assign private IP address to the OUTDOOR

AP/CPE in your local area network(LAN). The default LAN IP address is 192.168.2.1,
changing IP address will also change the DHCP server’s IP subnet.

DVANCED

OUTING

In this section, allow to configure routing feature in the OUTDOOR AP/CPE.

◆

Destination

— The IP address of packets that can be routed.

◆

Type

— Defines the type of destination. ( Host: Signal IP address / Net: Portion of

Network )

◆

Netmask

— Displays the subnetwork associated with the destination.

◆

Gateway

— Defines the packets destination next hop

◆

Interface

— Select interface to which a static routing subnet is to be applied

◆

Comment

— Help identify the routing

◆

RIP

— Enable or disable the RIP(Routing Information Protocol) for the WAN or LAN

interface.

Содержание WL-STATION-N2








































Результаты поиска

Содержание WL-STATION-N2

Отзывы:

Похожие инструкции для WL-STATION-N2

Бренды по названию

Популярные бренды

Solwise WL-STATION-N2, Руководство пользователя

Результаты поиска

Содержание WL-STATION-N2

Отзывы:

Похожие инструкции для WL-STATION-N2

Бренды по названию

Популярные бренды