Sollae Systems CIE-H10A Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 80

background image

CIE-H10A User Manual Ver. 1.1

- 11 -

https://www.ezTCP.com

1.6

Interface

1.6.1

Input Ports

Because each of CIE-H10A

’

s input ports are isolated by photo-couplers, users don

’

t need

to worry about the polarity. The circuit of the input port is shown in the figure below.

Figure 1-7 a circuit of the input port

The voltage specification of the input port is as follows:

Over 2.2V

H

1

Under 1.2V

L

0

Max. Input Voltage

24V

Polarity

Auto Polarity

Table 1-3 the voltage specification of the input ports

The input port is interfaced with a 5mm terminal block. Thus, use a (-) shaped

screwdriver to connect it with the user device.

⚫

Types for giving input
The type of the input ports is a wet contact by photo-couplers, which needs two
wires with different voltage levels to make an input signal. Needed a dry contact, you
can use a DCA(Dry Contact Adapter) so that you can give an input signal (ON or
HIGH) with switch (relay) interface.



The input ports are designed only for monitoring signals.

«
...
10
11
12
13
14
...
»

Содержание CIE-H10A

















































































Отзывы:

Нет отзывов

Похожие инструкции для CIE-H10A

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: Jabra Страницы: 4

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Taoglas Страницы: 2

Бренд: RadioMaster Страницы: 49

SUPERREMOTE UR19A

Бренд: X10 Страницы: 3

Бренд: Xantech Страницы: 102

Бренд: Xantech Страницы: 17

Бренд: X10 Страницы: 2

Бренд: Bartlett Страницы: 7

SaunaLogic SL2 Control

Бренд: Finnleo Страницы: 14

Бренд: Case IH Страницы: 81

PersonalWorkplace Pro Video

Бренд: G&D Страницы: 56

Бренд: Beninca Страницы: 16

Бренд: Graco Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды