EN
Instructions for using the Solight 1D11 GSM alarm
Dear customer, thank you for purchasing our product. Please carefully read and abide by the following instructions to ensure that
this product is used safely and to your complete satisfaction. This will also help avoid any improper use or damage. Prevent any
unskilled handling of the device and always follow the principles of use for electrical appliances. Store these instructions in a safe
place. For use in the home or indoors. The product should only be used by adults. Never expose the device to high levels of
humidity (e.g. in a bathroom), and prevent the product from coming into contact with liquids. Do not allow the device to be placed
near or come into contact with home electronics or computers.
Before installing the product, read all of the instructions
carefully in order to fully understand all the features.
Contents of package and description of each part
The package includes the main unit, remote control and swivel wall bracket
1. LED indicator
2. PIR sensor for motion detection
3. Speaker
4. Slot for SIM card
5. Touch keypad
6. Microphone
7.
“Learning code“ button
8. Battery compartment
9.
“Learning code“ button
10.
“ARM“ button (turns on the alarm)
11.
“CLR“ button (turns off the alarm)
12. LED indicator
13. Swivel battery cover
Inserting a SIM card
1.
The device requires the use of a SIM card without a PIN code.
Before inserting the SIM card, check that it does not have a
PIN set. If so, override it with a mobile phone. To override the PIN refer to your mobile phone user manual.
2. Insert the SIM card into the slot on the right side (front view) of the main unit with the contact area upwards and the slanted
corner in the upper left corner. An audible click indicates that the SIM card has been correctly inserted and cannot fall out.
3. If you want to remove the SIM card from the device, press it to release the lock.
Note:
The device is only compatible with standard SIM cards. MicroSIM, Nano SIM and other scaled types are not compatible.
Scaled types can be used only with an adapter. The adapters are available from your mobile service supplier.
Inserting the batteries
1. Use a Phillips screwdriver to unscrew the two screws on the back of the unit.
2. Insert three 1.5V AA batteries. Pay attention to the marked polarity. Use only alkaline batteries. After inserting the last battery,
the device emits a short beep, indicating that the batteries have been correctly inserted. Do not close the battery cover yet; in
the following sections you will need to access the keyboard, which is inaccessible with the cover on.
3. Put a screwdriver into the groove of the battery cover on the back of the remote control
and turn it to the left. Open the cover
and insert the CR2032 battery with the positive pole upwards. Close the cover and turn right to
lock it.
Assigning remote controls to the main unit
The alarm is disabled by default. Only when disabled it is possible to assign remote controls and other accessories. To assig n a
remote control to the main unit,
press and hold button 7 “Learning code” on the back of the main unit, and at the same time, press
button 9 “Learning code” on the remote control. Release the buttons when you hear a double beep. This means that the pairing
was successful. Other accessories that can be purchased separately can be paired this way.
Unpairing:
If you need to unpair a remote control or an accessory from the main unit, press and hold button 7 while removing one
of the batteries for at least
for
5 seconds. Keep on holding the button and reinsert the battery. You will hear a triple beep that
indicates that all of the paired devices have been erased from the memory. Then release button 7.
Note:
The maximum transmission range is 80m without obstacles
Activating the keypad
The keypad can be activated only when the alarm is disabled. After activating the keypad, press button 7. You will hear a short
beep that confirms that the keypad has been successfully activated. Enter commands by softly touching each of the keys. Each
successful touch is indicated with a short beep. The keypad is automatically locked after 15 seconds of inactivity.
1
5
6
4
2
7
3
8
12
10
13
11
9
