Solidyne 2600 serie, Руководство пользователя

Страница: 10 / 45


In case of damage on the internal fuses, it can be ordered as
spare parts. See Chapter 4
Phone lines protection
The telephone lines must have protection against
lightning and electrical surges. Please, see general
protection diagram at the end of this chapter.
2.2.6 PAIR A CELL PHONE
Any Bluetooth (c) cell phone can be linked to
Solidyne 2600. The phone can be up to 5 meters
away from the console, but it’s recommended
leave it near to the mixer, but not over the
console .
The procedure to link the mobile phone to the
console is similar to that used for other
Bluetooth (c) devices.
When the cell phone and console are paired, the
cell phone stores the ID of the console. This
operation is performed only once (for each
phone). Once the console and mobile are paired,
the console automatically connects to the cell
phone when the Bluetooth (c) link is enabled on
both devices.
Procedure:
•
At the console: Check at the Master Module
that the button BLUETOOTH [21] is off. When
Bluetooth (c) is on, it flash slowly (one flash ev-
ery 2 seconds). In this case, turn off Bluetooth
pressing and holding until the button stops
flashing.
•
At the console enable the “discovery” mode.
This mode only can be accessed if Blue-
tooth (c) is turned off. Being the Bluetooth (c) off ,
press and hold the button BLUETOOTH until
the LEDs blinks fast (approx. 10 seconds). It
indicates that Master 2608 is in “Discovery”
mode, to be found by the cell phone.
•
At the cell phone: start a search for a Blue-
tooth (c) device. This procedure can vary ac-
cording to the brand and model of cell phone.
Please refers to the owner’s manual.
•
When the search ends, look for the 2600’s
Bluetooth
(c)
device, which will appear as Soli-
dyne BTM641. If the cell phone ask for a
password, enter 0000 and confirm (see the
user’s manual of the cell phone).
•
The ID of the Solidyne 2600 is now stored in
the cell phone. The devices are "paired". The
user don’t need to repeat this operation while
using the same phone. BLUETOOTH button
now flash slowly (one flash every 2 seconds),
to indicate "Bluetooth
(c)
active".

On some phones you need to "connect" the new
device found to stay active. In others, the new
device is enabled after being detected.
2.2.6.1 Re-connect a paired phone
To reconnect to the console a cell phone, proceed
as follow:
•
Turn on the Bluetooth (c) on 2600 by pressing
"BLUETOOTH" until the button lights (5 secs
approx). The button will flash slowly in blue.
•
Enable the Bluetooth (c) at the cell phone.
When the cell phone notice that the connec-
tion was successfully the cell phone link are
ready. When make or receive a call, the au-
dio is routed to the console.

In some phones the re-connection is not automatic. You
need to "connect" the new device found to stay active.
2.2.6.2 Set up the level
IMPORTANT: At the cell phone, Bluetooth
volume must be adjusted at maximum level
in order to obtain a good reception and to sure
the best signal to noise ratio.
This adjusting must be done with a real calling using
Bluetooth.
The volume of the phone's speaker is not the same of
Bluetooth device. If you change the phone's level with-
out make a Bluetooth calling, you will only be changing
the volume for the phone's speaker, not for the Blue-
tooth. To change the level of Bluetooth, make a call us-
ing the console (or a hands free headset) and set the
Bluetooth level to the maximum, or one step below
the maximun. This setting is stored at the cell phone's
memory. If you use another cell phone with the con-
sole, you will need to set the Bluetooth level again.
2.2.6.3 Turn off Bluetooth at the console
To turn off, press and hold “BLUETOOTH” until the
button CELL PHONE stop flashing.
2.2.7 External Hybrid
The female TRS ¼” labeled “EXT HYBRID” gives
PGM send (tip) and return from Hybrid (ring), to con-
nect an external Hybrid. The PGM send is Mix-minus:
it includes all the signals of the PGM Bus, with excep-
tion of the
Return from Hybrid , to avoid a feedback
loop.
The signal that is incoming by the external hybrid’s re-
turn, is routed to the same circuit of control that the
signals of the internal hybrid. Therefore, the "Hybrid
Fader" will behave in the same way that it works with
the telephone lines connected to the console; sending
the signal to the air or to CUE according to the fader
position. When connects an external hybrid, the inter-
Page 10 Broadcast mixing consoles - 2600 series solidynepro.com