background image

ASSEMBLY & INSTALLATION - THRU-THE-WALL (CONT.) 

  

Refer to the SUPPORT BRACKET ASSEMBLY in the 
WINDOW MOUNTING section to assemble the support 
brackets. A wooden strip nailed to the outside wall should 
be used in conjunction with the angled sill support brack-
ets. 

5.  Screw or nail the cabinet to the wooden frame using 

shims if the frame is oversized, to eliminate possible 
noise. Remember to maintain proper slope for water 
elimination. 

6.  Install the chassis into the cabinet by following the 

steps described in the WINDOW MOUNTING section. 

 

OPTIONAL

: Caulking and installation of the trim on the 

interior wall may be done if desired. Caulk the openings 
around the top and sides of the cabinet and all sides of the 
wood sleeve to the opening. 
 

NOTE

: See the WINDOW MOUNTING instructions for the 

bottom rail seal location. 
 
 

MASONRY CONSTRUCTION 

 
1.  Cut or build a wall opening in the masonry wall similar 

to the frame construction (refer to the THRU-THE-
WALL installation for a wall thickness greater than 8 
1/2”)..  

2.  Secure the cabinet in place using masonry nails, or 

masonry anchor screws. Or, build a frame using the 
instructions found in the THRU-THE-WALL installation 
section. 

3.  Make sure the masonry above the cabinet is supported 

well. Use the existing holes in the cabinet or additional 
drilled holes to fasten the cabinet at various positions. 
Make sure that the side louvers are clear of any ob-
structions. 

4.  Install the exterior cabinet support brackets according 

to the SUPPORT BRACKET INSTALLATION instruc-
tions in the THRU-THE-WALL installation section. 
Caulk or flash with aluminum if needed. This will pro-
vide a tight seal around the top and sides of the cabi-
net. 

5.  For a more aesthetically pleasing installation, apply 

wood trim molding around the sides of the cabinet with-
out obstructing the side louvers. 

 

 

 

 

 

 

 

 

 

 

Support 

Bracket 

Wooden Strip 

FIG. 3 

FIG. 4 

 

13

 

Содержание SG-WAC-25ESE-C

























Отзывы: