background image

ASSEMBLY & INSTALLATION (CONT.) 

  

Installing the Chassis into the Cabinet 

1.  Team lift (two people) the air conditioner chassis and 

carefully slide it into the cabinet. Let the front of the air 
conditioner hang out approximately 6”. 

2. 

CAUTION: 

DO NOT PUSH ON THE CONTROLS OR 

FINNED COILS. 

3.  Be sure the chassis is firmly seated in the back of the 

cabinet. 

4.  Insert all screws removed during window installation 

and reattach the front face plate, front panel, and the 
air filter. Use the REMOVE CHASSIS instructions and 
figures 1-6 for reference. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 

THRU-THE-WALL INSTALLATION 

 

NOTE

: Consult local building codes prior to installation 

and/or a qualified carpenter. 
 

Select the Wall Location

 

This air conditioner has a slide-out chassis, so that it can 
be installed through an outside wall as specified below: 

MAX WALL THICKNESS

: 8 1/4” 

IMPORTANT

: The side louvers must never be blocked. 

NOTE

: All parts needed for Thru-The-Wall Installation are 

provided, except a wood frame, shims, and 10 wood 
screws (10-1” long minimum). Select a wall surface that: 
1.  Does not support major structural loads such as the 

frame construction at ends of windows, and under 
truss-bearing points, etc. 

2.  Does not have plumbing or wiring inside. 
3.  Is near existing electrical outlets, or where another out-

let can or will be installed. 

4.  Does not have objects blocking the air vents which 

limits cooling. 

5.  Allows unblocked airflow from the rear and sides of the 

air conditioner. 

 

Prepare the Wall

 

1.  Prepare the wall in frame construction (including brick 

and stucco veneer). Working from inside the room, find 
the wall stud that is nearest the center of the installa-
tion area. 

2.  Cut a hole on each side of the center stud. 
3.  Measure between the inside edges of every other stud 

as shown below. 

 

 

 

 

 

 

 

 

 

FIG. 1 

 

1

1

 

Содержание SG-WAC-25ESE-C

























Отзывы: