background image

  

 

OPERATING THE REMOTE CONTROL 

 The swing button turns on louver 
oscillation. 

 Press the ON/OFF button to turn the    
A/C on or off. When the unit is turned 
off, the Timer and sleep functions will be      
cancelled. The set temperature will be 
saved. 

 Press the MODE button to change the 
operating mode. You can choose AUTO, 
COOL, SAVE (energy saver), FAN only, 
or HEAT. The temperature will not be            
displayed when AUTO mode is selected. 

 Press the SLEEP button to turn SLEEP 
mode on or off. SLEEP mode is set to 
off automatically. When SLEEP mode is 
selected the timer can be adjusted. 
SLEEP mode is not available in Fan or 
Auto mode. 

 Press the FAN button to turn change the 
FAN options. You can choose between 
four speeds and auto mode. The fourth fan 
option is only available in cooling, heating 
and energy saver modes.   

NOTE: Make sure there are no obstructions between the receiver on the A/C and the 
remote control. Do not drop or throw the remote control. Do not allow water to get 
inside the remote control and do not place the remote control in direct sunlight or a 
place where it is very hot. 

Содержание SG-TTW-09ESE-26


















Отзывы: