background image

ASSEMBLY & INSTALLATION (CONT.) 

 9 

 
 
 
 
 
 
 
 
 

 

 

Placing the Cabinet Inside the Window 

1.  Open the window and place the cabinet in the middle 

of the window sill.  

2.  Make sure the bottom rail is seated over the window 

sill as shown below. Bring the window down temporar-
ily behind the top angle rail to hold the cabinet in place. 

3.  Fasten cabinet to window sill using two 3/4” HEX-Head 

screws. Pre-drill holes if needed. Add the bottom rail 
seal over the screws. 

Top Angle Rail and Side Bracket Installation

 

 
1.  Place the air conditioner on a hard flat surface. 
2.  Locate the foam gasket and top angle rail 
3.  Attach the foam gasket to the top angle rail 
4.  Install top angle side to cabinet as shown in FIG 7 

5.  Slide the “I” section of the window panel into the side 

bracket of the cabinet (FIG. 8a ). Do this for both sides. 

6.  Insert top and bottom legs of window filler panel frame 

into channel in the top angle and bottom rail. Do both 
sides. Install side retainer to cabinet as shown. FIG 8B-
9. 

 
 

 

FIG. 7 

Foam Gasket and Top 

Angle Rail 

 

 

 

SILL 

BOTTOM 

RAIL 

FIG. 8a 

FIG. 8b 

FIG

TOP

 

VIEW

 

Содержание GM-WAC-25ESE-C

























Отзывы: