Solaronics Residential Garage Heater Скачать руководство пользователя страница 1

Form RH-IOM-11

210080

Residential Garage Heater

Installation, Operation, & Maintenance

Instruction Manual

(Mount a copy of these instructions adjacent to the heater)

MODEL IDENTIFICATION

Record the information from the product identification label here for future reference.

Heater Model No.: _________________________  Heater Serial No.: ________________________

Rating: __________ BTUH   Type of Gas: Nat ___   LP/Propane ___    Date Installed ____________

FOR YOUR SAFETY

IF YOU SMELL GAS:
1. Extinguish any open FLAME.
2. Do NOT try to light any appliance.
3. OPEN windows.
4. Do NOT touch electrical switches; do
    NOT use any telephone in the house.

5. CALL your gas supplier immediately
    from a NEIGHTBOR’S home.  Follow the
    gas supplier’s instructions.
6. IF you can’t reach your gas supplier,
    CALL the FIRE DEPARTMENT.

FOR YOUR SAFETY

Do not store or use GASOLINE or other FLAMMABLE VAPORS or LIQUIDS in the vicinity of
this or any other appliance.

This unit is not to be installed in indoor living/sleeping areas.

!! WARNING !!

THESE INSTRUCTIONS must be carefully read and completely understood BEFORE
attempting to install , operate, or perform maintenance service on this GAS-FIRED
APPLIANCE.  Installation and Service MUST be performed by a QUALIFIED service agency,
installer, contractor, or gas supplier.  Failure to comply with the manufacturer’s instructions can
result in unsafe operation, property damage, personal injury, and/or death.  A gas-fired
appliance can expose you to substances in fuel or from fuel combustion which have been
determined by the State of California to cause cancer, birth defects, or other reproductive
harm.  Contact factory for further information.  Keep these instructions for future reference.

EXPLANATION OF HAZARD INTENSITY LEVELS

DANGER

:  Failure to comply 

WILL

 result in severe personal injury, death, and/or property damage.

WARNING

:  Failure to comply could result in severe personal injury, death, and/or property damage.

CAUTION

:  Failure to comply could result in minor personal injury, and/or property damage.

This manual is to be left with the owner after installation of this unit.

OWNER:  Store this manual in a safe place to furnish your serviceman with the necessary

information for servicing.

QUESTIONS?  Call the factory:  Monday – Friday   8 a.m. to 5 p.m.   Eastern Time

Содержание Residential Garage Heater





























Отзывы: