SOLARFOCUS Vampair, Руководство по установке

Страница: 2 / 52

1 About this manual 3
1.1 Limitation of liability 3
2 Safety information 3
3 Technical requirements 3
3.1 Warranty, guarantee, liability 3
3.1.1 Technical requirements for warranty and gua-
rantee claims 3
3.1.2 Conditions for claims 4
3.1.3 Claims rendered void 4
3.1.4 Limitation of liability 4
3.2 Standards, guidelines, regulations 5
3.3 Specifications for cooling mode 5
3.4 Installation location, installation position 5
3.5 Foundation for the heat pump 6
3.6 Line routing, connection 6
3.7 Heating system fill-up water 7
3.7.1 Avoiding scale buildup 7
3.7.2 Avoiding water-side corrosion 7
3.8 Information about the hydraulic connection 8
4 Product information 9
4.1 Product description 9
4.2 Functional components 10
4.3 Scope of delivery 11
4.4 Principle of operation 12
4.5 Innovative technologies 13
4.6 Dimensions 13
4.7 Accessories 13
4.8 Technical specifications 14
5 Prepare heat pump 17
5.1 Transport 17
5.2 Attach sealing tape 18
5.3 Dismantling the cover 18
5.4 Remove cladding 18
5.5 Remove transport lock 18
5.6 Connect the heat pump to the power supply
before commissioning 18
6 Install electric heating element 19
6.1 Important information 19
6.2 Heating element and components 19
6.3 Mount heating element 20
6.4 Connect the heating element 20
6.5 Fit the sensors (2x) in the heating element 21
7 Hydraulic connection 22
7.1 Make condensate drain, seal 22
7.2 Rinse the lines 22
7.3 Install the primary circuit circulation pump 22
7.4 Connect the primary circuit 23
7.4.1 Connection on the condenser 23
7.4.2 Cut insulating mat (only required for K 08 and K 10) 23
7.4.3 Primary circuit connection set 23
7.4.4 Fit temperature sensor T1 for condenser 26
7.4.5 Heat pump pipe 26
7.5 Pipe dimensions: Residual delivery height
information 27
7.5.1 vampair K 08, K 10 27
7.5.2 vampair K 12, K 15 27
8 Electrical connection 28
8.1 Access to terminal area 28
8.2 Terminal assignment 28
8.3 Seal the connection cable piping 29
8.4 Terminal area, electrical supply 30
8.5 Electrical connection plan 31
8.6 Connect ecomanager-touch control 32
8.6.1 Overview 32
8.6.2 Surface-mounted installation 32
8.6.3 Display power supply 32
8.6.4 Connect CAN bus 32
8.6.5 Connect RS485 bus 33
8.7 Connect electronic module D1 33
8.7.1 Terminal assignment - overview 33
8.7.2 Connection of the bus cable 33
8.7.3 Bus terminating resistor 34
8.7.4 Connect the primary circuit circulation pump 34
8.7.5 Connect the flow sensor 35
8.7.6 Heating circuit - switch externally (optional) 35
8.7.7 Connecting the mains power supply to the elec-
tronic module 35
8.7.8 Device address of the electronic module 36
8.7.9 Elec. fuses in the electronic module 36
8.8 Outside temperature sensor - position 36
8.9 Connecting the control to the internet 36
8.10 Smart Grid Ready 36
9 Initial commissioning 37
10 Foundation plan 38
10.1 Downward line connection 38
10.2 Line connection to the rear 41
10.3 Condensate drain 41
11 Flat roof set-up 42
12 Plant schematic 45
2 Installation manual vampair
Content