manualshive.com logo in svg

SolarEdge StorEdge Solution with Backup, Руководство по установке

Поделиться
Скачать
SolarEdge StorEdge Solution with Backup Скачать руководство пользователя страница 47

 

WARNING!

If the inverter  was operating properly (power was produced by the power 

optimizers), the following message is displayed. 

D C   V O L T A G E   N O T   S A F E
D O   N O T   D I S C O N N E C T  
V D C :      7 2 . 0

This message is displayed until the DC voltage is safe (50V). Do not open the 

cover until the voltage is safe or until at least five minutes have passed. 

 

AVERTISSEMENT!

 

La tension de sécurité par défault est de 50V. 
Ne pas ouvrir le couvercle ou les connecteurs DC jusqu'à ce que la tension soit 
affichée comme sécurisé ou jusqu'à ce que cinq minutes au moins se soient 
écoulées.

 2.  Turn the Connection Unit to OFF.

 3.  Turn the Connection Unit (if applicable) to OFF.

 4.  Disconnect the AC to the inverter by turning OFF the circuit breakers on the 

distribution panel. 

 5.  Release the  Allen screws holding the inverter cover and remove the cover.

 6.  Open the Allen screws of the inverter cover  and carefully pull the cover horizontally 

before lowering it.

CAUTION!

When removing the inverter cover, make sure not to damage the internal 
components. SolarEdge will not be held responsible for any components 
damaged as a result of incautious cover removal.

ATTENTION!
Lors du retrait du couvercle, assurez-vous de ne pas endommager les 
composants internes. SolarEdge ne peut être tenue pour responsable des 
composants endommagés à la suite d'une imprudence dans le retrait du 
couvercle.

Step 1: Activating the System

 1.  Verify that the inverter ON/OFF switch is OFF.

 2.  Verify that the StorEdge Connection Unit ON/OFF switch is in the OFF position. 

 3.  Remove the inverter cover: Open the inverter cover’s six Allen screws and carefully 

pull the cover horizontally before lowering it.

StorEdge Solution with Backup MAN-01-00262-1.5

46

   Step 1: Activating the System

Содержание StorEdge Solution with Backup



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды