SolarEdge Smart EV Charger Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 57

SolarEdge Smart EV Charger Скачать руководство пользователя страница 18

Main Procedures

The Smart EV Charger is supplied with a mounting bracket kit.

1. Mount the Smart EV Charger bracket

2. Mount the Smart EV Charger on the bracket

3. Connect the Smart EV Charger cable to the Smart EV Charger

4. Set the circuit breaker rating DIP switches

5. Plug in the AC plug

Follow the detailed procedures in the following sections to mount and connect the

Smart EV Charger

To mount the Smart EV Charger bracket:

Figure 3: Mounting bracket

1. Determine the Smart EV Charger mounting location, on the mounting surface.

2. Maintain the following minimum clearance areas between the Smart EV Charger and

other objects:

8" from the top and sides of the Smart EV Charger

At least 18" from the bottom of the Smart EV Charger if installing it indoors, 24” if

outdoors. If you are connecting the Smart EV Charger directly to the AC leave

sufficient clearance for the conduit as well.

3. Position the mounting bracket against the mounting surface and mark at least three

drilling hole locations (refer to

Mechanical Specifications on page 52 for mounting

Smart EV Charger Installation MAN-01-00657-1.0

17

Main Procedures

«
...
16
17
18
19
20
...
»

Содержание Smart EV Charger


























































Отзывы:

Нет отзывов