manualshive.com logo in svg

SolarEdge SE100KUS, Руководство по установке

Поделиться
Скачать
SolarEdge SE100KUS Скачать руководство пользователя страница 62

Chapter 6: Setting Up Communication  

The inverter sends the following information to the monitoring platform:

Power optimizer information received via the DC power lines (the PV output 

circuit).

Inverter information 

Information of any other connected devices.

 

This chapter describes setting up communication between: 

The inverter and the monitoring platform through the Internet (wired/ 

wireless), or through a cellular connection.

Multiple inverters  for a master/slave configuration.

Communication setup is not required for power harvesting, however it is needed for 
using the monitoring platform.

NOTE

 It is recommended to connect  communication connections before 
connecting the AC, for easier access to the communication board. 

CAUTION!

When connecting the communication cables, make sure that the ON/OFF/P 
switch on the Connection Unit is turned OFF, and the AC is turned OFF.

When configuring the communication parameters, make sure that the 
ON/OFF/P switch on the Connection Unit is OFF, and the AC is turned ON. 

Chapter 6: Setting Up Communication      

61

Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.2

Содержание SE100KUS








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды