SolarEdge Firefighter Gateway Скачать руководство пользователя страница 33

Страница: 33 / 61

: The total number of slaves detected on the specific port

Dev

: The type of device that was configured to a specific port (based on the port’s

functionality), as follows:

: SolarEdge device (default)

LGR

: Non-SolarEdge logger

MLT

: Multiple devices, such as meters and batteries

: Home automation devices (for Smart Energy)

PROT

: The protocol type to which the port is set:

For a SolarEdge device:

RS485 protocol

ZigBee protocol

: SolarEdge slave

: SolarEdge master

P2P

: ZigBee point-to-point

MPM

: ZigBee multipoint master (for the

ZigBee gateway or for load management by

the inverter)

MPS

: ZigBee multipoint slave (for a ZigBee

router card)

For electricity meters, refer to the

application note - Connecting an

Electricity Meter to SolarEdge Devices at

http://www.solaredge.com/files/pdfs/solaredge-meter-installation-guide.pdf

: SunSpec - for a non-SolarEdge logger (monitoring and control)

Configuration Menu Options

This section describes basic Firefighter Gateway configuration options.

To enter Setup mode:

1. Verify that the SolarEdge Firefighter Gateway is connected to a power outlet.

2. Press the Enter button until the following message is displayed:

P l e a s e e n t e r
P a s s w o r d
* * * * * * * *

Firefighter Gateway Installation Guide MAN-01-00113-1.4

Configuration Menu Options

Содержание Firefighter Gateway






























































Результаты поиска

Содержание Firefighter Gateway

Отзывы:

SolarEdge Firefighter Gateway, Руководство по установке, Страница: 33 / 61

Результаты поиска

Содержание Firefighter Gateway

Отзывы: