Sokkia iX-1001 Скачать руководство пользователя страница 97

Страница: 97 / 177

15. SETTING-OUT MEASUREMENT

6. Press

[OK]

to return to <Key in coord>. Set the

next setting out point to continue setting out
measurement.

To find a point where a target cannot be directly installed, perform REM setting-out measurement.



"12.5 REM Measurement"

PROCEDURE

1. Install a target directly below or directly above the

point to be found. Then use a measuring tape etc.
to measure the target height (height from the
survey point to the target).

2. Select "Setting out" in <Menu> to display <Setting

out>.

3. Set the instrument station, and, if necessary, enter

data for Backsight setup.



"15.2 Distance Setting-out Measurement"

steps 2 to 3

4. Select "SO data setting" In <Setting out> to

display <SO data setting>.
Press

[Shvr]

until the distance input mode is

"SO.Height.". Input height from the surveying point
to the position to be set out in "SO.Height". If
necessary, input the angle to the point to be set
out. Enter values and press

[OK]

15.4 REM Setting-out Measurement

Содержание iX-1001


















































































































































































Результаты поиска

Содержание iX-1001

Отзывы:

Sokkia iX-1001, Руководство оператора, Страница: 97 / 177

Результаты поиска

Содержание iX-1001

Отзывы: