Sokkia iX-1001 Скачать руководство пользователя страница 76

Страница: 76 / 177

13. COORDINATE MEASUREMENT

Enter instrument station coordinates,instrument
height (HI) and target height (HR).

4. Press

[OK]

to set the input values. <Backsight

setup> is displayed again.

Based on the instrument station coordinates and backsight station coordinates which have already been set,
the azimuth angle of the backsight station is calculated.

PROCEDURE Entering coordinates

1. Select "Backsight setup" in <Coordinate>.

• <Backsight setup> can also be displayed from

the screen in step 4 of "13.1 Entering Instrument
Station Data".

2. Tap the screen title to display popup and select

"Key in coord" display. Enter the backsight station
coordinates.

•

[SRCH]

: Performs Auto Pointing. Rotates the

instrument in the direction of the backsight.

•

[Azimuth] /[H.ANG]/[None]/[0 SET]

: Switches

horizontal angle setting method.





Horizontal angle settings"

13.2 Azimuth Angle Setting

Содержание iX-1001


















































































































































































Результаты поиска

Содержание iX-1001

Отзывы:

Sokkia iX-1001, Руководство оператора, Страница: 76 / 177

Результаты поиска

Содержание iX-1001

Отзывы: