Sokkia iX-1001 Скачать руководство пользователя страница 66

Страница: 66 / 177

11. ANGLE MEASUREMENT

The instrument automatically turns from the reference direction to the specified angle (target).

• instrument also turns to the target coordinates when reference angle is omitted.



• Rotation may not be completed correctly when specifying an angle near the zenith or nadir if "Tilt crn" or "Coll.

crn" is set to "Yes" in <Angle/Tilt>.



"19.1 Observation Conditions - Angle/Tilt"

PROCEDURE

1. Sight the point you will use as the reference angle

and set it as the reference angle.
Sight the reference point and press

[0SET]

, or

input the reference point angle.



"11.1 Measuring the Horizontal Angle

between Two Points (Horizontal Angle 0°)"/
"11.2 Setting the Horizontal Angle to a
Required Value (Horizontal Angle Hold)"

2. Press

[MOTOR]

Enter the vertical and horizontal angles in the
Motor display.

3. After confirming the angle, press

[TURN]

. The

instrument moves to the point (target) entered in
step 2.

11.3 Turning the Instrument from the Reference Angle to a Specified Angle

Содержание iX-1001


















































































































































































Результаты поиска

Содержание iX-1001

Отзывы:

Sokkia iX-1001, Руководство оператора, Страница: 66 / 177

Результаты поиска

Содержание iX-1001

Отзывы: