manualshive.com logo in svg

Sokkia iX-1001, Руководство оператора, Страница: 157 / 177

Поделиться
Скачать
Sokkia iX-1001 Скачать руководство пользователя страница 157

153

24.TARGET SYSTEM

Select a prism or a target depending on your purpose. The following are all special accessories (sold 
separately).

An appropriate prism for Auto Pointing and Auto Tracking measurement: "10. TARGET SIGHTING AND 
MEASUREMENT 

 Appropriate prism for Auto Pointing and Auto Tracking"

• When using a reflecting prism equipped with a target for distance and angle measurements, be sure to direct 

the reflective prism correctly and sight the center of the prism target accurately.

• Each reflective prism has its own prism constant value. When changing prisms, be sure to change the prism 

constant correction value.

Reflecting Prism System (AP Series)

Use an appropriate system for iX.
The figure on the right is an example.
Because all reflecting prisms and accessories have standardized 
screws, it is possible to combine these prisms, accessories, etc. 
according to your objectives.
Prism constant correction value : -40 (used alone)
Aperture

: 58 mm

360° Prism (ATP1), 360° Sliding Prism (ATP1SII)

These 360

°

 prisms reduce the possibility of "lost prism" during Auto 

Tracking measurement regardless of the direction of the prism.
3D positioning accuracy (standard deviation)

: 3mm (Horizontal acceptance 

angle: 360° (full transit). Angles of 
elevation and inclination both less 
than 20°)

Prism constant correction value : -7
Recommended value for aperture: 34 mm

• Recommended value for aperture does not mean the actual 

aperture of the 360

°

 prism because it is a collection of prisms.

Pinpole prism (OR1PA)

Prism constant correction value : -30 (used alone)
Aperture

: 25 mm

Reflective sheet target (RS series)

Prism constant correction value : 0
Aperture

: Target size

2-point target (2RT500-K)

This target is used for two-distance offset measurement.
Prism constant correction value: 0
Aperture

: 50 mm

ATP1

ATP1SII

Содержание iX-1001


















































































































































































Отзывы:

Нет отзывов