Sokkia iX-1001 Скачать руководство пользователя страница 156

Страница: 156 / 177

152

23.POWER SUPPLY SYSTEM

Operate your instrument with the following combinations of power equipment.



An appropriate prism for Auto Pointing and Auto Tracking measurement: "10. TARGET SIGHTING AND
MEASUREMENT



Appropriate prism for Auto Pointing and Auto Tracking"



• When using an external battery, mount the BDC70 in place to maintain the balance of the instrument.
• Never use any combination other than those indicated below. If you do, the instrument could be damaged.

Those indicated by * are standard accessories. Others are optional accessories.



• Dedicated power cables differ according to the country or the area where the instrument is used. Contact your

local dealer for the details.

• By using the Y cable (EDC211) the instrument can perform RS232C communication (D-sub 9-pin) at the

same time as connecting to an external power source.



External power supply equipment

• Use an external battery (BDC60A/61A) with the charged standard battery (BDC70) to fulfill the sufficient

operating time and to maintain the balance of the instrument.

• When using the Car cigarette lighter cable (EDC115), leave the car engine running. Use the 12 V DC battery

with the negative side grounded.

• When using the Power cable (EDC213), be sure to stop the car engine before use. Connect the red clip to

the positive side of the 12 V DC battery and the black one to the negative side.

%'&$
9'&
$K$K

BDC70

CDC68A

('&
WR9$&

&'&

('&

('&
9'&

EDC113A/C
(110 to 240 VAC)
EDC113B
(110 to 125 VAC)
etc.

Charger

External battery

For car cigarette lighter

AC/DC converter

Battery*

Charger*

Power cable*

Interface cable

('&

<&DEOH

('&

('&
WR9$&

('&

<&DEOH

Power cable

('&

Power cable

Interface cable

AC/DC converter

Car battery

Содержание iX-1001


















































































































































































Результаты поиска

Содержание iX-1001

Отзывы:

Sokkia iX-1001, Руководство оператора, Страница: 156 / 177

Результаты поиска

Содержание iX-1001

Отзывы: