manualshive.com logo in svg

Sokkia iX-1001, Руководство оператора, Страница: 134 / 177

Поделиться
Скачать
Sokkia iX-1001 Скачать руководство пользователя страница 134

130

19. CHANGING THE SETTINGS

Perform a cold boot to return all items to factory settings. A cold boot will not erase surveying data in instrument. 
However, if the data in the memory is important, BE SURE TO TRANSFER IT TO A PERSONAL COMPUTER 
BEFORE PERFORMING A COLD BOOT.

• The password function will not be canceled.
• Resume function will be canceled.

PROCEDURE

1. "To perform a cold boot, while holding 

{

} 

and

 {S.P.}

, press

 

the power key on the side of the instrument.

"All Settings will be cleared. Are you sure?" is displayed.

2. Press

 [YES] 

to continue. 

• Select 

[NO]

 and press 

{Enter}

, or press

 {ESC} 

to cancel.

3. When the power is ON after the a cold boot, the screen for configuring the touch panel is displayed. 

Configure the touch panel to continue.

"8.1 Configuring the Touch Panel"

19.14 Restoring Default Settings

Содержание iX-1001


















































































































































































Отзывы:

Нет отзывов