manualshive.com logo in svg

Sokkia iX-1001, Руководство оператора, Страница: 113 / 177

Поделиться
Скачать
Sokkia iX-1001 Скачать руководство пользователя страница 113

109

19. CHANGING THE SETTINGS

Ang.reso. (Angle resolution)

: iX-1001/1002/501/502: 0.5", 1"*

iX-1003/1005/503/505: 1"*, 5"

 Automatic tilt angle compensation mechanism

The vertical and horizontal angles are automatically compensated for small tilt errors using the 2-axis tilt 
sensor.

• Read the automatically compensated angles when the display has stabilized. 
• The horizontal angle error (vertical axis error) fluctuates according to the vertical axis, so when the 

instrument is not completely leveled, changing the vertical angle by rotating the telescope will cause the 
displayed horizontal angle value to change. 

• Compensated horizontal angle = Measured horizontal angle + Tilt in angle/tan (Vertical angle)
• When the telescope is directed close to the zenith or nadir angle, tilt compensation is not applied to the 

horizontal angle.

Collimation correction

The instrument has a collimation correction function that automatically corrects horizontal angle errors 
caused by horizontal axis and leveling axis errors. Normally set this item to "Yes".

V mode (vertical angle display method) 

Select "Obs.condition" in <Configuration> and select "Dist".

19.2 Observation Conditions - Dist

Zenith

Horiz

Horiz 90°

Содержание iX-1001


















































































































































































Отзывы:

Нет отзывов