manualshive.com logo in svg

Softing BC-700-PB, Руководство пользователя, Страница: 53 / 60

Поделиться
Скачать
Softing BC-700-PB Скачать руководство пользователя страница 53

Chapter 14 - Notes on battery use

PROFIBUS Tester BC-700-PB - User Manual

53

14

Notes on battery use

14.1

Lithium backup battery

CAUTION

This product contains a lithium-metal backup battery!

The lithium content is not more than 1 g. The battery has been successfully tested by the
manufacturer in accordance with the UN Manual of Test and Criteria (test procedures of
Part III, Sub-Section 38.3).

Improper handling of lithium batteries can cause the batteries to ignite or explode and pose
a burn hazard to users. If the product is properly handled, this battery does not need to be
replaced during the lifetime of the product. Therefore, opening the product is unnecessary
and not permitted. The product must only be operated within the specified temperature
range. Do not expose to heat above this temperature range and keep away from open fire.
Store in a dry place.

14.2

Rechargeable battery pack

14.2.1 Guidelines and warnings on battery use

Read and understand these safety instructions and warnings before
using or charging your rechargeable battery pack

Failure to read and follow the below instructions may result in fire, personal
injury and damage to property if charged or used improperly.

CAUTION

The rechargeable battery pack contains < 2 g Lithium.

Softing Industrial Automation GmbH, its distributors or retailers assume no liability for
failures to comply with these warnings and safety guidelines.

By purchasing this battery, the buyer assumes all risks associated with lithium
batteries. If you do not agree with these conditions, return the battery immediately
before use.

Never charge batteries unattended. When charging the battery pack you should
always remain in constant observation to monitor the charging process and react to
potential problems that may occur.

We recommend, to charge the Lithium-ion battery inside the device via the external
AC adaptor.

If at any time you witness a battery starting to “balloon” or swell up, discontinue
charging process immediately, disconnect the battery and observe it in a safe place
for approximately 15 minutes. This may cause the battery to leak, and the reaction
with air may cause the chemicals to ignite, resulting in fire.

Содержание BC-700-PB





























































Отзывы:

Нет отзывов