Sofar solar 3.3K- 5.5KTL-X Скачать руководство пользователя страница 25

Страница: 25 / 83

SOFAR 3.3K~12KTL-X

User manual

Shenzhen SOFARSOLAR Co ., Ltd.

- 20 -

Step 1

Remove the insulation layer of an appropriate length according to

figure 4-3, then insert the AC output cable though the PG waterproof cable
gland.

Figure4-3 AC Output Cable schematic diagram

Step 2

Connecting the AC output power cable: The AC output

cable(R,S,T,N and PE) is connected to the terminal block, as shown in
figure 4-4.

Figure4-4 Cable connection schematic diagram

4.4. Connecting Communications Cables

Meter/CT

RS485 Connecting Communications Cables

are used for meter communication,

the electricity meter is shown in the fig.

①

Cables

correspond to 24,25

respectively on the electricity meter, as shown in fig.

③

The connection mode is

shown in fig.

②

. In position. 2, 5, 8, 10 were respectively connect wires with

corresponding inverter R, S and T phase and zero line is linked together, the
second will be connected to the R phase CT S1 (red) received a position 1
meter, S2 (black) received the meter position. 3, in the same way connected to

Содержание 3.3K- 5.5KTL-X



















































































Результаты поиска

Содержание 3.3K- 5.5KTL-X

Отзывы:

Бренды по названию

Популярные бренды

Sofar solar 3.3K- 5.5KTL-X, Руководство пользователя

Результаты поиска

Содержание 3.3K- 5.5KTL-X

Отзывы:

Бренды по названию

Популярные бренды