Sofar solar 1.1K-3.3KTL-G3 Скачать руководство пользователя страница 27

Страница: 27 / 73

SOFAR 1.1K~3.3KTL-G3

User manual

- 22 -

Interface

DVC

PV input interface

DVCC

AC output interface

DVCC

USB interface

DVCA

RS485 interface

DVCA

CT interface

DVCA

Logic interface

DVCA

WiFi/GPRS/Ethernet interface

DVCA

4.1. Electrical connection

Figure 4-1 Shows the flowchart for connecting cables to the inverter.

4.2. Connecting PGND Cables

Connect the inverter to the grounding electrode using protection ground

(PGND) cables for grounding purpose.

The inverter is transformer-less, requires the positive pole and

negative pole of the PV array are NOT grounded. Otherwise it will cause

inverter failure. In the PV power system, all non current carrying metal

parts (such as: PV module frame, PV rack, combiner box enclosure,

inverter enclosure) should be connected to earth.

Attention

Prerequisites:

The PGND cables are prepared (

≥

4mm

outdoor power cables are

recommended for grounding purposes),the color of cable should be yellow-green.

Procedure:

Step 1

Remove the insulation layer with an appropriate length using a wire

Start

Connect PGND
cable

Connect DC
input cable

End

Connect AC output
power cable

Connect communication
cables (not mandatory)

Содержание 1.1K-3.3KTL-G3










































































Результаты поиска

Содержание 1.1K-3.3KTL-G3

Отзывы:

Бренды по названию

Популярные бренды

Sofar solar 1.1K-3.3KTL-G3, Руководство пользователя

Результаты поиска

Содержание 1.1K-3.3KTL-G3

Отзывы:

Бренды по названию

Популярные бренды