Socal Moto Gear GL18FGN Скачать руководство пользователя страница 1

© Copyright 2015 SoCalMotoGear. All Rights reserved. 

Ver. 1.5

        

                                                                                                                                

 

Page 1 of 4

 

 

INSTALLATION INSTRUCTIONS 

GL1800 LED FOG LIGHT KIT 

 

2001-2010 PART NO. GL18FGN (NON-AIRBAG) 
2006-2010 PART NO. GL18FGA (WITH AIRBAG) 
2012+          PART NO. GL18FGA (WITH OR WITHOUT AIRBAG) 

 

 

 

 

        

       L.E.D.   

 

 
Congratulations on your purchase!  

 

This product is intended for aftermarket use and have been fit checked on stock, non-modified OEM motorcycles. As with any aftermarket products, 
there may be some slight modifications required.  In some cases, minor modifications such as drill-out of a bigger hole may be necessary on the part  
itself or onto your motorcycle. If you are not comfortable with any installation steps, please consult a qualified motorcycle technician to perform the 
work. Always allow bulbs to cool down before touching them.  

 

Non U.S. Motorcycles: This kit may not be Plug and Play on non U. S. spec motorcycles. 

 

PARTS LIST 

 

LETTER  QTY 

 

 

LED FOG LIGHT 

RIGHT MOUNTING BRACKET 

LEFT MOUNTING BRACKET 

4MM SPACER 

20MM SPACER 

16MM SPACER 

SMALL FLANGE INSERT 

M5 X 18MM SCRW 

LARGE FLANGE INSERT 

LARGE RUBBER GROMMET W/BRACKET 

2MM SPACER 

M6 FLANGE (LONG) BOLT 

M6 FLANGE (SHORT) BOLT 

JUMPER WIRE [non-pictured] 

-- 

SPRING 

M5 X 30MM SCREW  [non-pictured] 

-- 

FLAT WASHER 

SMALL RUBBER GROMMET 

W/LIGHT BRACKET  [non-pictured]

 

-- 

ZIP TIE 

ON/OFF SWITCH 

FOG LIGHT WIRE HARNESS 

 

INSTALLATION STEPS: 

 

 

 

STEP 1.

 Place motorcycle on center stand. 

 

IMPORTANT – 

The memory settings of the suspension system, trip meter, clock, and radio will be lost when disconnecting the negative battery cable. 

Reset your settings after reconnecting the battery. 
 

STEP 2. 

Disconnect the negative cable from the battery.  

 

STEP 3. 

Remove the lower front cowl following the repair manual instructions. 

 
STEP 4.  Skip this step if you currently have fog lights installed. Remove your existing lights and proceed to Step 5. 

Using cutters, remove the plastic knockouts from the lower front cowl and smooth edges with a Dremel® or file.

 

 
STEP 5. 

Locate the Left (indicated on the back with an “L”) and the Right (indicated on the back with an “R”) Mounting brackets and set aside. 

 

To see our Installation Video, please visit: 

www.SoCalMotoGear.com/foglights 

 

 

(A) 

 
 

 

 

 

 

(F) 

          

    (K)                              (B) 

                                                                                         
                                                                                                  
(D) 
 

(M)    

                                                                                             

(I) 

             (D) 

 

         (I) 
 

 

 

     (E) 

 

 

     

   

 (N) 

                                                                                (I)                                                      
                                         (J) 

                               (K)                                                      

               

 

                         (L) 

           (G) 

 

(H) 

(R)                           (Q) 

(P) 

 (J) 

(C) 

 

(O) 

(O) 

Отзывы: