SnowWolf AlphaBlower 33-100-H Скачать руководство пользователя страница 49

Страница: 49 / 98

AlphaBlower Operation and Maintenance Manual

Maintenance

Cutting Edge Replacement

NOTE: Replace or flip the bolt-on cutting edge

when it wears within 1/2” - 3/4”.
Replace only with genuine SnowWolf
cutting edge and hardware.

1. Park the machine on a level surface with the

snow blower properly attached.

2. Lower the snow blower approximately three to

four inches off the ground.

3. Engage the parking brake.

4. Shut off the machine's engine, remove the

ignition key (if equipped), wait for all moving
parts to come to a stop and relieve all pressure
in the hydraulic lines.

5. Block and/or support the snow blower with

proper lifting device capable of sufficiently
supporting the unit's weight.

6. Disconnect PTO and hydraulic connections

between the snow blower and the tractor.

7. Block the cutting edge, remove the fasteners

and remove the cutting edge.

NOTE: Be cautious as the cutting edge and

hardware may be sharp.

8. Properly dispose of the old cutting edge(s) and

install the new cutting edge(s) by reversing the
steps listed here.

NOTE: Replace worn or damaged fasteners as

needed.

Содержание AlphaBlower 33-100-H



































































































Результаты поиска

Содержание AlphaBlower 33-100-H

Отзывы:

Похожие инструкции для AlphaBlower 33-100-H

Бренды по названию

Популярные бренды

SnowWolf AlphaBlower 33-100-H, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание AlphaBlower 33-100-H

Отзывы:

Похожие инструкции для AlphaBlower 33-100-H

Бренды по названию

Популярные бренды