SnowPure Electropure EXL Series Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 81

SnowPure Electropure EXL Series Скачать руководство пользователя страница 46



SNOWPURE, LLC, 2005-2018

VERSION 3.5 (XL+EXL)

–FEBRUARY 2018

PAGE 46

Feed Water

Electropure’s EDI feed water specifications are designed to minimize any maintenance
that the module may require for normal and sustained operation. Some service may be
required if substandard feed water is introduced to the module and/or insufficient power
is applied during operation.

Key foulants are TOC, hardness, silt particles, and iron.

Hardness (scale) deposits

If feed high in specific solutes is introduced into the EDI, deposits (hardness scale) may
form within the concentrating compartments, and consequently, product water quality will
diminish. Water high in hard ions (Ca

+2

, Mg

+2

), dissolved CO

2

, and high in pH

contributes to rapid scaling. To remove carbonate scale, the concentrate stream must
be cleansed with an approved acid solution. See Appendix #1 for procedure for acid
cleaning.

Ion-exchange resins (TOC organic fouling)

Feed water containing organic (TOC) contaminants will foul the ion-exchange resins and
membranes  with  a  film  that  can  deleteriously  affect  ion  transfer  rate,  and  therefore
product water quality.  When this occurs, the purified stream must be cleansed with an
approved  non-ionic  organic  remover.    This  may  be  either  an  approved  non-ionic
surfactant  or  an  approved  caustic  based  cleaner.    See  Appendix  #2  for  procedure  for
organic cleaning.

Particulate fouling

Coarse  debris  in  the  EDI  feed  will  block  portions  of  the  flow  distribution,  and  unequal
distribution  of  water  within  the  module  will  lead  to  lower  performance.    Fine  particles
(e.g., silt) in the EDI feed will foul the resins and the concentrate streams.  A very fine
filter is recommended before the EDI especially if the EDI is fed from an RO tank and not
directly  from  the  RO  permeate.    A  good,  strong  water  flush  of  the  plumbing  before
installation  of  the  EDI  modules  should  prevent  debris  from  entering  the  modules.    See
the feedwater specifications for particulates.

Power and Regeneration

If an EDI module operates without power or with insufficient power, the resin beads and
membranes  can  become  saturated  with  ions  and  the  purity  of  the  product  water  will
diminish.   To  purge  the resin  of  ions,  initiate the flow  of  water through  the  module  and
gradually increase the voltage of the power supply.  The module will draw more current
than normal as ions are transported out of the system  and the resins are regenerated.
Caution: care should be taken not to exceed the output limitations of the power supply if
over-current protection is not provided.

Chapter 7: Cleaning and Maintaining your EDI Modules

«
...
44
45
46
47
48
...
»

Содержание Electropure EXL Series


















































































Отзывы:

Нет отзывов