background image

X  

XX  

6

Step 7: 7-1) Take off the sleeves of the

coupling cables.

(For 4.0HP)

Figure 2

Risk of injury from machine

tipping over

Work slowly and carefully,

especially if you change direction.
Guide the machine up or down the slope
not crosswise to it.
Watch out for obstacles, do not work
near inclines.
Do not use the machine on slopes with a

radient greater than 20%

Let engine and machine adjust to
outdoor temperatures before starting
to clear snow.

Clear snow immediately after it has 

stopped snowing, later on the 
underneath layer will ice up and will
make clearing the snow more
difficult.
If at all possible, clear snow in the
direction of wind.
Clear the snow in such a way that
tracks you have cleared, overlap
slightly.

Starting the engine (see “Starting

the engine”)

Starting the engine (see “Starting

the engine”)

Press the coupling lever (1) and
hold it down; the worm in use.

As a result of the worm

establishing contact with ground,
the machine moves forward.
If you want to increase the travel
speed, raise the side handle (8)
slightly; the worm has greater
contact with the ground and then 
drives the machine forward faster.
This leads (if repeated frequently)
to the rubber lip on the worm
wearing down faster.
To reduce the travel speed, press 
down on the side handle.

For 4.0HP

If you want to change gear, first
release the coupling lever for the
drive system (2) and then change
gear with the shift lever (6).
(In some machines)
The machine is fitted with
freewheeling levers (3 and 4).
Using these, enable the machine to
be steered more easily:

-- To the right: Pull on the right

freewheel lever (4)/

--To the left: Pull on the left

freewheel lever (3).

Step 6: Assemble the gear shift lever.

5-2) Fix the knighthead to

7-2) Connect the sleeves to

Figure 10

coupling levers.

7-3) Connect the sleeves to the

coupling cables.

5-3) Adjust the knighthead

and make sure the whorl and the

throw-out chute gear completely
match and tighten the knighthead
screw, lock the rocker to the 
knighthead.

left handle bar.

Working on slopes

Tip on clearing snow

Set the direction and distance

of throw

17

Содержание SP 1128 HD













Отзывы: