background image

1. Introduction

1 - 2

PLATFORM

The MB20

/

26J platform is large enough for two operators indoors, one outdoors and  has 

a free-draining perforated floor with 150 mm toeboards. Hand-rails are constructed  from 

Steel tubing and a safety drop-bar is provided at the entrance. Safety restraint  harness 

anchor points are also fitted in the floor of the platform. These must be used at  all times. 

The main controls are fitted to this platform.

PLATFORM CONTROLLER

The primary (Upper) control box is permanently fitted to the front of the platform. It features 

a joystick which provides proportional control for raising or lowering the mast, raising or 

lowering the jib or rotating the complete mast assembly. The same joystick is also used to 

drive and steer the machine.
A safety Interlock Switch or ‘deadman button’ is incorporated into the Joystick. It must be 

activated at all times in order to operate any function. This feature allows for one-handed 

operation. A comprehensive explanation of control functions is given in the Operators 

Manual - a copy of which shall be located in the platform document wallet located just 

beneath the upper control station in the platform.

The secondary (Lower) control box is fitted to the mast cover at arm level. It features a 

‘deadman’ enable button and selector buttons to provide pre-programmed speeds for all 

functions except drive and steering. This control station is used primarily for service-type 

operations including pre-operation inspection. It should never be used to position a manned 

or unmanned platform. It may be used in the event of emergency, however, to lower the 

manned platform.

ELEVATING ASSEMBLY

The platform is raised and lowered by a combination of a steel jib and a series of 

telescoping mast sections. The main hydraulic cylinder, mounted within the masts, lifts the 

2nd mast directly. The other masts are connected by a system of heavy duty plate chains 

and pulleys to ensure sequential lifting. 
A parallel system of heavy duty straps ensures that the masts descend in the proper 

sequence and also ensure that a mast cannot be held in suspension by an obstacle during 

descent.
The jib cylinder provides a lifting arc to the jib and cage assembly. All hydraulic functions 

are carried out using solenoid operated control valves. Each cylinder features an integral 

holding valve to prevent uncontrolled descent in the case of a hose bursting.

!

!

DO NOT use the work platform without guardrails properly 

assembled and in place.

W A R N I N G

!

!

NEVER

 operate the machine from the upper controls until the 

platform entrance drop-bar is in the fully lowered position and the 

safety harness is fitted.

W A R N I N G

Содержание MB20J

































Отзывы: